background image

ACCESSORIES 

 

 

TMC7 Series

 

 

Page 18 

710-02887-00A 

 

Examples 

Command: Start 

Message 

Starter 

Address 

Function 

Code 

Register 
Address 

Data 

CRC 

In 20 06 40002 1 

CRC1, 

CRC2 

Out 20  06  40002  1 CRC1, 

CRC2 

 
Starter Status: TMC7 Running 

Message 

Starter 

Address 

Function 

Code 

Address / 

Bytes Read 

Number / 

Value 

CRC 

In 20 03 40003  1 

CRC1, 

CRC2 

Out 

20 

03 

   xxxx0011 

CRC1, CRC2 

 
Trip Code: Motor overload 

Message 

Starter 

Address 

Function 

Code 

Address / 

Bytes Read 

Number / 

Value 

CRC 

In 20 03 40004  1 

CRC1, 

CRC2 

 

 

5.4 Profibus 

Module 

 

Part Number: TMC7-PBM-01 

 
The Profibus Module can be used with the TMC7 to enable control and monitoring via a Profibus network. 

 

Adjustment Address

 

 

Data rate 

The interface has data rate auto-detection so no adjustment is required for this

 

Low Voltage Switchgear (LVSG) 
Motor Starter Format 1 Profile Basic Data Structure 

 

Master > Slave Control Word is structured as follows. 

 

BYTE 1 

Bit 7 

Bit 6 

Bit 5 

Bit 4 

Bit 3 

Bit 2 

Bit 1 

Bit 0 

Reserved Reserved

 

Reserved

 

Reserved

 Reset 

Reserved

 

Reserved

 Fwd 

Run 

BYTE 2 

Bit 7 

Bit 6 

Bit 5 

Bit 4 

Bit 3 

Bit 2 

Bit 1 

Bit 0 

Reserved Reserved Reserved 

Quick Stop 

Reserved Reserved Reserved Reserved 

 

Slave > Master Status Word is structured as follows. 

 

BYTE 1 

Bit 7 

Bit 6 

Bit 5 

Bit 4 

Bit 3 

Bit 2 

Bit 1 

Bit 0 

Reserved Reserved Reserved Reserved Reserved

 Fault 

On 

Ready 

BYTE 2

 

Bit 7 

Bit 6 

Bit 5 

Bit 4 

Bit 3 

Bit 2 

Bit 1 

Bit 0 

Ramping 

Reserved

 

 

Motor Current (% FLC) 

1

 

 

1

 Only available from TMC7 units with serial number format xxxxx-4 or greater. 

ADDRESS

MSD

LSD

Содержание TMC7 Series

























Отзывы: