Toshiba RBM-A101UPVA-E Скачать руководство пользователя страница 31

Страница: 31 / 45

– 30 –

Terminal DI2 / DI2: External trouble Input

• An AHU fan operation monitor (Field supply), could be attached at this dry contact terminal (For example, the

abnormality of the fan motor). A closed contact generates the check code L30.

Terminal DI3 / DI3: Forced thermostat OFF Input

• When signal input, AHU is in “thermostat-off” status forcibly.

Terminal DI4 / DI4: Notice code Input

• If there is input, a spanner mark will be displayed on the remote controller. The system will not stop.

Check “DN settings” for the setting method.

Terminal DI5 / DI5: Operation Mode Input (Cool / Heat)

• Cool / Heat mode selection over a dry contact.
If the contact is short-circuited, system changes to heat mode.If the contact is open, system changes to cool mode.

• Only cool mode and heat mode are available.

When Bit4 of SW502 is turned on in DDC type, capacity demand can be achieved by short-circuiting Terminals DI2 to

DI4.

* If all are short-circuited, the DI3 function has priority.

When SW701 is ON (no voltage), apply a voltage of DC12 V ± 10% and wiring as follows.

Terminal DI6 / DI6: External ON/OFF Input

• When using with DDC, it starts by turning on this terminal.

Function

Terminal

OPEN

SHORT

Mode Input Cool / Heat

DI5 / DI5

COOL mode active

HEAT mode active

Short - circuit

Cooling step

Heating step

DI2

DI3

DI4

TCB-IFDMX01UP-E

(Terminal block without relay)

TCB-IFDMR01UP-E

(Terminal block with relay)

DI2 - DI4

DI2 -

DI4

MAX. 1 m

Locally procured

SIGNAL (+)

Signal Voltage (DC12 V ± 10%)

SIGNAL (-)

GND

Normally open

(+)

(-)

DI6

MAX. 100 m

Locally procured

(Input, DC5 V)

Relay coil signal

Same as on the left

30-EN

Содержание RBM-A101UPVA-E














































Результаты поиска

Содержание RBM-A101UPVA-E

Отзывы:

Похожие инструкции для RBM-A101UPVA-E

Бренды по названию

Популярные бренды

Toshiba RBM-A101UPVA-E, Руководство по установке

Результаты поиска

Содержание RBM-A101UPVA-E

Отзывы:

Похожие инструкции для RBM-A101UPVA-E

Бренды по названию

Популярные бренды