Toshiba RAV-SM564KRT-E Скачать руководство пользователя страница 40

Страница: 40 / 91

– 40 –

Possible causes

Abnormal outdoor unit discharge temperature

(

∗

) Protection device of

Outdoor unit high-pressure system error

outdoor unit is activated.

Four-way valve system error (judged by indoor unit)

Outdoor unit: Malfunction of fan

Protection device of

Outdoor unit: Inverter Idc activated

Outdoor unit: Position detect error

outdoor unit is activated.

Header and follower indoor units in the group are not running due to the following alarm.

(Alarm code: E03, L03, L07, L08)

Heat exchange sensor (TCJ) error

Heat exchange sensor (TC) error

Indoor unit sensor error

Room temperature sensor (TA) error

Discharge temperature sensor (TD) error

Temperature sensor (TE, TS) error

(

∗

) Outdoor unit sensor error

Outside air temperature sensor (TO) error

Failure of indoor unit EEPROM

Compressor breakdown

Compressor locking

(

∗

) Outdoor unit

Current detect circuit error

compressor system error

Outdoor unit low-pressure system error

Duplication of header indoor unit

Auto address

Group connection indoor unit for individual indoor unit

∗

If group configuration or

address at power on is invalid,

Group address not set

the unit enters enters address

setting setting mode automatically.

No setting (indoor unit capacity)

Duplication of indoor unit collective address

Other errors of outdoor unit (

∗

)

Others

External interlock error

Phase sequence error

Troubleshooting (Continued)

Outline of judgment (Contenued)

Lamp indication

Operation Timer Preparing

Alternate blinking

Operation Timer Preparing

Alternate blinking

Operation Timer Preparing

Alternate blinking

Operation Timer Preparing

Simultaneous blinking

Operation Timer Preparing

Blinking

Operation Timer Preparing

Simultaneous blinking

Operation Timer Preparing

Simultaneous blinking

Check code

P03

P04

P19

P22

P26

P29

P31

F01

F02

F10

F04

F06

F08

F29

H01

H02

H03

H06

L03

L07

L08

L09

L20

L29

L30

L31

(

∗

) Check code detected by outdoor unit is a typical example. It varies with outdoor unit of combination.

For details, see the Service Manual of applicable outdoor unit.

⎫

⎬

⎭

⎫

⎪

⎬

⎪

⎭

⎫

⎪

⎬

⎪

⎭

⎫

⎪

⎬

⎪

⎭

⎫

⎪

⎬

⎪

⎭

⎫

⎪

⎬

⎪

⎭

⎫

⎪

⎬

⎪

⎭

Содержание RAV-SM564KRT-E




























































































Результаты поиска

Содержание RAV-SM564KRT-E

Отзывы:

Похожие инструкции для RAV-SM564KRT-E

Бренды по названию

Популярные бренды

Toshiba RAV-SM564KRT-E, Руководство по обслуживанию

Результаты поиска

Содержание RAV-SM564KRT-E

Отзывы:

Похожие инструкции для RAV-SM564KRT-E

Бренды по названию

Популярные бренды