Toshiba RAV-SM1104CT-E Скачать руководство пользователя страница 3

Страница: 3 / 22

– 2 –

Ceiling Type

Installation Manual

Ceiling Type

Installation Manual

Definition of Protective Gear

When the air conditioner is to be transported, installed, maintained, repaired or removed, wear protective gloves
and ‘safety’ work clothing.

In addition to such normal protective gear, wear the protective gear described below when undertaking the special
work detailed in the table below.

Failure to wear the proper protective gear is dangerous because you will be more susceptible to injury, burns,
electric shocks and other injuries.

Work undertaken

Protective gear worn

All types of work

Protective gloves
‘Safety’ working clothing

Electrical-related

work

Gloves to provide protection for electricians and from heat

Insulating shoes

Clothing to provide protection from electric shock

Work done at heights

(50 cm or more)

Helmets for use in industry

Transportation of

heavy objects

Shoes with additional protective toe cap

Repair of outdoor unit Gloves to provide protection for electricians and from heat

Warning indications on the air conditioner unit

Warning indication

Description

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote electric power supplies before servicing.

WARNING

Moving parts.
Do not operate unit with grille removed.
Stop the unit before the servicing.

CAUTION

High temperature parts.
You might get burned when removing this panel.

CAUTION

Do not touch the aluminium fins of the unit.
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before the operation, otherwise there might be

the burst.

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote
electric power supplies
before servicing.

WARNING

Moving parts.
Do not operate unit with grille
removed.
Stop the unit before the servicing.

CAUTION

High temperature parts.
You might get burned
when removing this panel.

CAUTION

Do not touch the aluminum
fins of the unit.
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before
the operation, otherwise there
might be the burst.

3-EN

4-EN

+00EH99878901_01EN.book Page 2 Wednesday, April 13, 2011 9:38 AM

Содержание RAV-SM1104CT-E























Результаты поиска

Содержание RAV-SM1104CT-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAV-SM1104CT-E, Руководство по установке

Результаты поиска

Содержание RAV-SM1104CT-E

Отзывы:

Бренды по названию

Популярные бренды