Toshiba RAV-HM301MUT-E, Руководство по установке

Страница: 19 / 27

– 18 –
 To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the
room, the detection temperature of heating can be
raised. Also use a circulator or other machinery to
circulate heat air near the ceiling.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[06]
for the Code No. in Procedure
4
.
• For the set data in Procedure
5
, select the set data
of shift value of detection temperature to be set up
from the following table.

Filter sign setting
According to the installation condition, the filter sign
term (Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[01]
for the Code No. in Procedure
4
.
• For the set data in Procedure
5
, select the set data
of filter sign term from the following table.
• The filter sign may be unavailable depending on the
remote controllers.
 How to set up swing type
The swing type of the louver can be selected.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[F0]
for the Code No. in Procedure
4
.
• Select the following data for the set data in
Procedure
5
.
• About “Dual swing”
“Dual” means that louvers 01 and 03 are directed
and swing in one direction and louvers 02 and 04 are
directed and swing in the opposite direction.
(When louvers
01 and 03 are directed downward,
louvers 02 and 04 are directed horizontally.)
• About “Cycle swing”
The four louvers swing independently at respective
timings.
CAUTION CAUTION
Do not set the swing set data to “ 0000 ”.
(This setting may cause a failure of the louvers.)

How to set up louver lock
(No swing)
A position of the individual louvers (four directions) can
be locked.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[F1]
,
[F2]
,
[F3]
, or
[F4]
for the Code No.
in Procedure
4
.
• Select the following data for the set data in
Procedure
5
.
* When (4) or (5) is selected, dew drop may occur
during cooling mode.
• When the setting has been determined, lights up.
Set data Detection temperature shift value
0000 No shift
0001 +1°C
0002
+2°C
(Factory default)
0003 +3°C
0004 +4°C
0005 +5°C
0006 +6°C
Set data Filter sign term
0000 None
0001 150 H
0002
2500 H
(Factory default)
0003 5000 H
0004 10000 H
Set data Swing of louvers
0001
Standard swing
(Factory default)
0002 Dual swing
0003 Cycle swing
(1)
0001
(2)
0002
(3)
0003
(5)
0005
(4)
0004
Set data

How to cancel louver lock
Set the wind direction to “ 0000 ” of the louver lock setup
procedure above.
• When the setting is cancelled, goes out.
Other operations are the same as those in “How
to set up louver lock (No swing)”.
 Remote controller sensor
The temperature sensor of the indoor unit senses room
temperature usually. Set the remote controller sensor
to sense the temperature around the remote controller.
Select items following the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[32]
for the Code No. in Procedure
4
.
• Select the following data for the set data in
Procedure
5
.
When flashes, the remote controller sensor is
defective.
Select the set data “
0000 ” (not in use) or replace the
remote controller.
 Communication type
When connecting to an indoor unit or central controller
dedicated to TCC-Link, it is necessary to change to
TCC-Link.
Follow to the basic opreration procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[FC]
for the Code No. in Procedure
4
.
• Select the set data “ 0000 ” (TCC-Link) in
Procedure
5
.
 Fan speed setting when
thermostat-OFF in cooling
mode
Set the fan speed when the room temperature reaches
the set temperature in the cooling mode.
Follow to the basic opreration procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[9A]
for the Code No. in Procedure
4
.
• Select the following data for the set data in
Procedure
5
.
04
[F4]
02
[F2]
03 [F3]
01 [F1]
Drain pipe Refrigerant pipe
0000
Setting data
Set data Remote controller sensor
0000 Not in use (Factory default)
0001 In use
Set data Communication type
0000 TCC-Link
0004 TU2C-Link (Factory default)
Set data
Fan speed when thermostat-OFF
in cooling mode
0000 Remote controller setting
0001
Extremely low speed (UL)
(Factory default)
35-EN 36-EN