background image

24-EN

23-EN

– 12 –

EN

 

„

Installation of outdoor unit

 

y

Before installation, check the strength and 
horizontalness of the base so that abnormal sounds 
do not emanate.

 

y

According to the following base diagram, 

fi

x the base 

fi

rmly with the anchor bolts.

  (Anchor bolt, nut: M10 × 4 pairs)

Drain hole

150

150

525

600

45

365

400

Drain hole

Drain nipple 
mounting hole

 

y

As shown in the 

fi

gure below, install the foundation 

and vibration-proof rubber pads to directly support 
the bottom surface of the 

fi

xing leg that is in contact 

with and underneath the bottom plate of the outdoor 
unit.

*  When installing the foundation for an outdoor unit 

with downward piping, consider the piping work.

Absorb vibration 

with vibration-proof 

rubber pads

Fixing leg

Foundation

Correct

Bottom plate of 

outdoor unit

Foundation

Correct

Support the bottom surface of the 

fi

xing 

leg that is in contact with and underneath 

the bottom plate of the outdoor unit.

Foundation

Incorrect

Do not support the 

outdoor unit only 

with the 

fi

xing leg.

If only the end of 

the 

fi

xing leg is 

supported, it may 

deform.

Set the out margin of the anchor bolt to 15 mm or less.

15 mm or less

 

y

When water is to be drained through the drain hose, 
attach the following drain nipple and waterproof 
rubber cap, and use the drain hose (Inner dia.: 
16 mm) sold on the market. Also seal knockout hole 
and the screws securely with silicone material, etc., 
to prevent water from leaking. 
Some conditions may cause dewing or dripping of 
water.

 

y

When collectively draining discharged water 
completely, use a drain pan.

Drain nipple

Waterproof rubber cap

(5 pcs.)

Waterproof rubber cap

Knockout hole

Drain nipple

 

„

For reference

If a heating operation is to be continuously performed 
for a long time under the condition that the outdoor 
temperature is 0°C or lower, draining defrosted water 
may be dif

fi

cult due to the bottom plate freezing, 

resulting in trouble with the cabinet or fan.
It is recommended to procure an anti-freeze heater 
locally in order to safely install the air conditioner.
For details, contact the dealer.

 WARNING

 

y

Be sure to install the outdoor unit in a place 
able to bear its weight.

  If strength is insuf

fi

cient, the unit may fall down 

resulting in human injury.

 

y

Perform speci

fi

ed installation work to protect 

against strong wind and earthquakes.

  If the outdoor unit is imperfectly installed, an 

accident by falling or dropping may be caused.

Obstacles in both front and rear of unit

Open above and to the right and left of the unit.
The height of an obstacle in both the front and rear of 
the unit, should be lower than the height of the outdoor 
unit.

Standard installation

1. Single unit installation

150 or  more

1,000 or 

more

2. Serial installation of two or more units

200 or  more

1,000 

or 

more

300 or 

more

300 or 

more

Serial installation in front and rear

Open above and to the right and left of the unit.
The height of an obstacle in both the front and rear of 
the unit, should be lower than the height of the outdoor 
unit.

Standard installation

1,000 or 

more

300 or 

more

200 or 

more

1,500 or 

more

2,000 or 

more

Содержание RAV-GV1101AT8P-E



























Отзывы: