SET
TIME
TIMER SET
TEST
FILTER
RESET
TEMP.
CL
FAN
SAVE
SWING/FIX
VENT
MODE
ON / OFF
UNIT LOUVER
1
3
2
4
1
3
2
4
◆
Start
1
Push
button.
The operation lamp illuminates, and the operation
starts.
2
Select an operation mode with the “
”
button.
One push of the button, and the display changes
in the order shown below.
(Dehumidify)
Auto
Dry
Cool
Fan
3
Select fan speed with “
” button.
One push of the button, and the display changes
in the order shown below.
Auto
High
Med.
Low
When fan is in “
Auto”, fan speed is
adjusted based on difference between set point
and room temperature.
The temperature sensor detects the return air
temperature at the indoor unit, which differs
from the room temperature depending on the
installation condition. Set point is a target of
room temperature. (
“Auto” is not selectable
in the Fan mode.)
4
Select the set point temperature by pushing
the “TEMP.
” or “TEMP.
” buttons.
◆
Stop
Push
button.
The operation lamp goes off, and the operation stops.
4
Correct
usage
• When the air conditioner is used for the
fi
rst time or when the setting is changed, follow the steps below. Settings
are saved in memory and are displayed anytime the unit is turned on by pushing the
button.
■
Preparation
• When the circuit breaker is turned on, the partition lines are displayed on the remote controller.
* After the circuit breaker is turned on, the remote controller does not accept any commands for approx. 1 minute,
this is not a failure.
REQUIREMENT
When the air conditioner is re-powered after it has not been used for a long period, turn on the circuit breaker at
least 12 hours before starting the air conditioner.
◆
Start
1
Push
button.
The timer mode changes with every push of the
button.
Off
(Off timer)
Off
(Repeat Off timer)
No display
On
(On timer)
•
and timer display
fl
ashes.
2
Push
to select “set time”.
• With every push of
button, the set time
increases by 0.5 hr (30 minutes). To set a time
more than 24 hours for timer operation, timer
can be set in increments of 1 hr. The maximum
set time is 168 hr (7 days). The remote control
displays the set time with time (between 0.5 and
23.5 hours) (*
1
) or number of days and time (24
hours or more) (*
2
) as shown below.
• With every push of
button, the set time
decreases by 0.5 hr (30 minutes) (0.5 - 23.5
hours) or 1 hr (24 - 168 hours).
Example of remote control display
•
23.5 hours (*
1
)
•
34 hours (*
2
)
Time
Number of days
shows 1 day (24 hours).
shows 10 hours. (Total 34 hours)
3
Push
button.
•
icon disappears and time display goes on,
and
or
icon
fl
ashes. (When On
timer is activated, time and On timer
are
icons and other icons disappear.)
4
Cancel timer operation.
Push
button.
Timer icon disappears.
NOTE
• When the operation stops after the timer reached
the preset time, the Repeat Off timer resumes the
operation by pushing
button and stops the
operation after the time of the timer has reached the
set time.
• When
is pushed while the Off timer function of
the air conditioner is active, the indication of the timer
function disappears and then appears again after
about 5 seconds.
This is due to normal processing of the remote
controller.
5
Timer
operation
• Three timer modes are available: (Setting of up to 168 hours is enabled.)
Off timer
: The unit stops when the set time is reached.
Repeat Off timer : The unit stops daily when the set time is reached.
On timer
: The unit starts when the set time is reached.
NOTE
Auto Changeover
• During Auto Mode, the unit selects the operating mode (cooling, or fan only) based on the user set point
temperature.
• If the Auto mode is uncomfortable, you can select the desired conditions manually.
Cooling
• If there is a demand for cooling, unit will start approximately 1 minute after mode is selected.
When the operation is attempted to restart after stop
When the unit is attempted to restart immediately after it was stopped, the unit can not start for approx. 3 minutes
this is to protect the compressor.
– 7 –
13-EN
14-EN
1115653808_EN.indd 7
1115653808_EN.indd 7
10/11/2559 BE 16:21
10/11/2559 BE 16:21
