PRESET OPERATION
AUTO RESTART OPERATION
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
QUIET
: Start and stop the operation.
Note:
Under certain conditions, QUIET operation may not provide adequate
cooling or heating due to low fan speed features.
For comfortable sleep, automatically control air
fl
ow and automatically turn
OFF the unit.
Press
COMFORT
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note:
For cooling operation, the set temperature will increase automatically
2°F (1°C)/hour for 2 hours (maximum 4°F (2°C) increase). For heating
operation, the set temperature will decrease.
COMFORT SLEEP OPERATION
18
To start the sleep timer (OFF timer) operation
Press
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
SLEEP TIMER OPERATION
Firstly, turn off the circuit breaker.
Filter Reset
FILTER lamp lights on; the
fi
lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when
needed.
• Do not use benzine, thinner, polishing powder or chemically-treated
duster.
MAINTENANCE
20
19
QUIET OPERATION
17
16
To automatically restart the air conditioner after a power failure (Power of the
unit must be on.):
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
2. Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blinks 5 times/sec
for 5 seconds)
• Do not operate ON timer and OFF timer.
Note:
Default setting of auto restart operation is on.
15
Set your preferred operation for future use. The settings will be memorized by
the unit for future operation (except air
fl
ow direction).
1. Select your preferred operation.
2. Press and hold
PRESET
for 3 seconds to memorize the setting.
The
P
mark displays.
3.
Press
PRESET
: Operate the preset operation.
The unit does not operate.
Cooling or Heating is abnormally low.
• The power main switch is
turned off.
• The circuit breaker is tripped.
• ON timer is set.
• The
fi
lters are blocked with dust.
• The temperature has been set
improperly.
• Windows or doors are open.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
SELF CLEANING OPERATION
(COOL AND DRY OPERATION ONLY)
21
To protect against odors caused by humidity in the indoor unit:
1.
If
the button is pressed once during “Cool” or “Dry” mode, the fan will
continue to run for other 30 minutes, it will then turn off automatically.
This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the
2 more times within 30
seconds.
TROUBLESHOOTING (CHECK POINT)
22
TEMPORARY OPERATION
TIMER OPERATION
14
Daily timer allows the user to set both, ON & OFF, timers. They will be
activated on a daily basis.
Setting Daily Timer
Setting the ON Timer
Setting the OFF Timer
1
Press
ON
: Set the desired
ON timer.
Press
OFF
: Set the desired
OFF timer.
2
Press
SET
: Set the timer.
Press
SET
: Set the timer.
3
Press
CLR
: Cancel the timer.
Press
CLR
: Cancel the timer.
• When every day timer is activated, two arrows ( , ) are indicated.
Note:
• Keep the remote control In an area accessible to transmit signal to the
indoor unit; otherwise, time lag of up to 15 minutes will occur.
• Last settings will be saved for the next operation.
1
Press
ON
: Set the ON
timer.
3
Press
SET
.
2
Press
OFF
: Set the OFF
timer.
4
Press
SET
button during
the ( or ) mark
fl
ashing.
Set the timer when the air conditioner is operating.
13
In case the remote control has been misplaced or
discharged:
• By pressing the RESET button, the unit starts or
stops without using the remote control.
• Operation mode is set to AUTOMATIC. Preset
temperature is 77°F (25°C) and fan operation is
automatic speed.
COOLING / HEATING / FAN ONLY OPERATION
DRY OPERATION
10
For dehumidi
fi
cation, a moderate cooling performance is controlled
automatically.
1.
Press
MODE
: Select Dry
.
2.
Press
TEMP
: Set the desired temperature.
9
1.
Press
MODE
: Select Cool
, Heat
, or Fan only
.
2.
Press
TEMP
: Set the desired temperature.
Cooling: Min. 62°F (17°C), Heating: Max. 86°F (30°C),
Fan Only: No temperature indication
3.
Press
FAN
: Select AUTO, LOW , LOW+
, MED
,
MED+
, or HIGH
.
Hi-POWER OPERATION
ECO OPERATION
12
To automatically control room to save energy (except in DRY and FAN ONLY mode)
Press
ECO
: Start and stop the operation.
Note:
For cooling operation, the set temperature will increase automatically
2°F (1°C)/hour for 2 hours (maximum 4°F (2°C) increase). For heating
operation the set temperature will decrease.
11
To automatically control room temperature and air
fl
ow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press
Hi-POWER
: Start and stop the operation.
1110655115-1_EN.indd 4
1110655115-1_EN.indd 4
18/11/56 10:01
18/11/56 10:01
Downloaded from
