Toshiba MMF-UP0151H-E, Руководство по установке

Страница: 10 / 30

– 9 –
Model MMF- A B C D E F G H J
UP015, UP018
200 50 107 132 157 210
6.4 12.7
80
UP024, UP027
9.5 15.9
UP036 to UP056 380 125 50 120 160 390 100
1750
80 30×3 30×3
600
40
25
210
815
631
59
10
20
120
120
180
40
165
*
92
*
■
External views
(R
oo
t
of
dr
a
in h
o
se
)
Bracket for
fixing to wall
Discharge port
Pitch
Pitch
Remote
controller
Piping port at rear side
(Dia.130 Knock-out hole)
Bracket for fixing to floor
(Both side)
Intake grille
Piping port at lower side
(50 x120 Knock-out hole)
Wall
Positioning for refrigerant piping
Connection port for refrigerant
piping (Liquid side G )
Connection port for refrigerant
piping (Gas side H )
Refrigerant piping port (Both side)
(
J
Knock-out hole)
Wiring hole (Both side)
(Dia.26 Knock-out hole)
* Drain hose drawing-out port (Both side)
(Dia.40 Knock-out hole)
*
Drain hose drawing-out port (Both side) is for only UP036 model to UP056.
To connect drain hose on right or left, route it through the knock-out for refrigerant piping on
UP015 to UP027 model.
(Unit: mm)
(O
pp
os
ite
si
de:
12
0)
F
A A
B
C
D
E
(Sold
separately)
Drain hose
(Length: 520 mm,
connection external dia.: 20 mm)
 Installation of indoor unit
REQUIREMENT
In case of installing the indoor unit to the floor and the
wall other than wooden floor and wall, the six anchor
bolts (M8 × L50 or longer) are required.
Procure them at the local site.
Fixing to the wall surface
Use the attached wall fixing bracket by inverting it at
upper side of the unit. Fix the indoor unit to the wall
surface using the attached screw bolts, anchor bolts or
etc. at two positions. Many holes for fixing the indoor
unit to wall surface and for fixing the indoor unit itself
are provided on the bracket. Sliding the bracket right
and left sides, select a position which can securely fix
the indoor unit and then fix it.
A hole on the wall fixing bracket for the indoor unit is a
long hole. Therefore the indoor unit can be fixed at any
position keeping clearance from 0 to 50 mm.
As shown below, it is also possible to fix the indoor unit
without inverting the bracket. (In this case, keep
clearance with length of head of the bolt between the
indoor unit and the wall.)
Fixing to the floor
Use the attached floor fixing bracket to fix the lower
right and left sides of the indoor unit to the floor.
To fix to the indoor unit, use the side plate screws and
use the screw bolts or anchor bolts for fixing to the floor
respectively, and then fix the indoor unit at total four
positions, two positions for right and left each.
(Unit: mm)
Indoor unit fixing figure
Wooden wall
Screw bolts
Concrete wall
Anchor bolts
0 mm 50 mm
177
0 mm
(F
ix
ing he
ig
ht
of
sc
rew
bo
lt or
an
chor
bol
t)
1730
m
m
(F
ix
ing he
ig
ht
of
sc
rew
bo
lt or
an
chor
bol
t)
Clearance
(Height of head
of fixing bolt)
Model MMF- A B
UP015 to UP027 88 30 to 80
UP036 to UP056 258 40 to 90
A
B
Wooden wall
Screws for
side plate
Concrete wall
Screws bolts
(Total 4 at right and left)
Screws for
side plate
Anchor bolts
(Total 4 at
right and left)
634 mm
Air intake grille
Bracket for
fixing to floor
Bracket for fixing to wall
Electrical control
box cover
17-EN 18-EN