Toshiba MMD-AP00244BH2UL страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 20

background image

– 7 –

◆

Installation of air filter

1

Remove the cover plate (Screw x 3).

All unit models have the FR - 1 & FR - 2 filter position option available. Both positions use the

same filters per model shown in the chart above.

Two positions for filter rack

FR-1

FR-2

Indoor unit

Cover plate

CAUTION

The cover plate is attached temporarily with the screws
indicated by the arrows for protection when shipped.
After reattaching it, seal the screw holes with tape
instead of using the screws.

Cover plate for filter

slot

Cover plate fixing

screws

2

Pull out the filter rack, and set the air filter (locally procured) in it.

3

Push the filter rack in fully and reattach the cover plate. (Screws x 2)

Filter rack

Air filter

(locally procured)

Air filter

(locally procured)

Screws

13-EN

14-EN

+00EH99881801_01EN.book Page 7 Friday, November 25, 2011 10:23 AM

«
...
6
7
8
9
10
...
»

Содержание MMD-AP00244BH2UL





















Отзывы:

Нет отзывов

Похожие инструкции для MMD-AP00244BH2UL

Бренд: GE Страницы: 72

Бренд: Haier Страницы: 122

A-VMH18DC-1 Service

Бренд: Heat Controller Страницы: 50

R410A Split Series

Бренд: Dakin Страницы: 40

Бренд: Vax Страницы: 16

Бренд: Daikin Страницы: 9

Бренд: dirna Bergstrom Страницы: 84

Бренд: CIAT Страницы: 18

Бренд: Crosley Страницы: 4

Бренд: FASANO TOOLS Страницы: 8

Бренд: HACE Страницы: 9

Pure & Clean Plus A1041A

Бренд: Aerus Страницы: 18

Бренд: ACPro Страницы: 20

Бренд: Daikin Страницы: 18

Бренд: Daikin Страницы: 26

VRV III-Q RQYQ140PY1

Бренд: Daikin Страницы: 33

Бренд: Daikin Страницы: 17

Бренд: Daikin Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды