background image

– 6 –

SMMS Floor Standing Type

Installation Manual

EN

SMMS Floor Standing Type

Installation Manual

„

Installation space

(Unit: mm)

Reserve sufficient space required for installation or service work.

REQUIREMENT

When using the air conditioner under condition of high humidity, attach the heat insulator to the side face and the rear 
side of the indoor unit.

„

Filter cleaning sign term setting

The lighting term setup of the filter sign (Notification of filter cleaning) of the remote controller can be changed 
according to the condition of installation.

 

For setup method, refer to “Filter sign setting” in the Applicable controls of this Manual.

200 or 

more

500 or more

10

00

 o

mo

re

Front side

(In case of right direction piping)

Front side

4

Installation

CAUTION

Strictly comply with the following rules to prevent damage of 
the indoor units and human injury.

• Do not put a heavy article on the indoor unit or let a 

person get on it. (Even units are packaged)

• Carry in the indoor unit as it is packaged if possible. If 

carrying in the indoor unit unpacked by necessity, use 
buffering cloth or other material to not damage the 
unit.

• Carry the package by two or more persons, and do not 

bundle it with plastic band at positions other than 
specified.

• Be sure to take measures to prevent falling at the wall 

surface and the floor and fix it surely considering 
prevention of accident of falling because this unit is 
formed into a thin type. If it is not fixed, a falling 
accident may occur.

• After carry in the indoor unit to the specified place, fix 

it to the wall and the floor immediately for safety.

„

Installation of indoor unit

Fixing to the wall surface

Use the attached wall fixing bracket by inverting it at 
upper side of the unit. Fix the indoor unit to the wall 
surface using the attached screw bolts, anchor bolts or 
etc. at two positions. A many holes for fixing the indoor 
unit to wall surface and for fixing the indoor unit itself 
are provided on the bracket. Sliding the bracket right 
and left sides, select a position which can securely fix 
the indoor unit and then fix it.

A hole on the wall fixing bracket for the indoor unit is a 
long hole. Therefore the indoor unit can be fixed at any 
position keeping clearance from 0 to 50 mm.
As shown below, it is also possible to fix the indoor unit 
without inverting the bracket. (In this case, keep 
clearance with length of head of the bolt between the 
indoor unit and the wall.)

Fixing to the floor

Use the attached the attached floor fixing bracket to fix 
the lower right and left sides of the indoor unit to the 
floor.
To fix to the indoor unit, use the side plate screws and 
use the screw bolts or anchor bolts for fixing to the floor 
respectively, and then fix the indoor unit at total four 
positions, two positions for right and left each.

(Unit: mm)

Wooden wall

Screw bolts

Concrete wall

Anchor bolts

Model  MMF-

A

B

AP015H to AP027H type

88

42 to 92

AP036H to AP056H type

258

52 to 102

0 mm

50 mm

17

70 mm

(Fixin

g

 he

ig

ht

 o

sc

re

w

 bo

lt an

an

ch

or

 b

ol

t)

1730

 m

m

(Fixin

g

 he

ig

ht

 o

sc

re

w

 bo

lt an

an

ch

or

 b

ol

t)

Clearance

(Height of head 

of fixing bolt)

A

B

Wooden wall

Screws for 

side plate

Concrete wall

Screws bolts

(Total 4 at right and left)

Screws for 

side plate

Anchor bolts

(Total 4 at 

right and left)

640 mm

11-EN

12-EN

+00EH99880501_01EN.book  Page 6  Thursday, April 7, 2011  10:15 AM

Содержание MMC-AP0154H-TR

























Отзывы: