Toshiba IP4100 Series Скачать руководство пользователя

Страница: 63 / 88

BASE STATION CONFIGURATION

Extensions Screen

IP4100 Install Sept., 2013

3-3

Extensions Screen

Table 3-1

Home/Status Options

Button or Option

Function

Reboot

Reboot the connected base station. If there are any
active calls on the base station, it will not reboot.

Forced Reboot

Disconnect any active calls and reboot the connected
base station.

Table 3-2

Home/status Parameters

Item

Definition

System Information

The current multi-cell state of this base station (Multi Cell Disabled or
Ready; Primary or Secondary).

Phone Type

Always IPDECT, a combination of VoIP and wireless DECT technology.

System Type

The signalling protocol used to communicate with the IPedge or Strata
CIX system.

RF Band

The DECT radio band currently in use by this base station.

Current Local Time

The current time and date received from the time server.

Operation Time

The amount of time since this base station was last rebooted.

RFPI-Address

The address assigned to the DECT radio of this base station.

MAC-Address

The address assigned to the Ethernet connector of this base station.

IP-Address

The current IP address assigned to this base station.

Firmware Version

The version of the current firmware on this base station.

Firmware URL

The address of the server this base station uses for firmware updates.

SIP Identity Status
on this Base station

The status of all handsets registered to this base station, in the format
{Extension}@{IP address of the IPedge or Strata CIX system}.

Содержание IP4100 Series

























































































Результаты поиска

Содержание IP4100 Series

Отзывы:

Похожие инструкции для IP4100 Series

Бренды по названию

Популярные бренды

Toshiba IP4100 Series, Руководство по установке

Результаты поиска

Содержание IP4100 Series

Отзывы:

Похожие инструкции для IP4100 Series

Бренды по названию

Популярные бренды