background image

TOSHIBA AMERICA INFORMATION SYSTEMS, INC. Contrat de licence de la 

Division des systèmes de télécommunication 

IMPORTANT : LE PRÉSENT CONTRAT DE LICENCE (« CONTRAT ») CONSTITUE UN ACCORD 
JURIDIQUE ENTRE VOUS (« VOUS ») ET TAIS. VEUILLEZ LE LIRE ATTENTIVEMENT. 
L’UTILISATION DE TOUT LOGICIEL ET DE TOUT RENSEIGNEMENT S’Y RAPPORTANT 
(ENSEMBLE, « LOGICIELS ») INSTALLÉ DANS UN PRODUIT NUMÉRIQUE OU EXPÉDIÉ À MÊME 
CE PRODUIT, OU QUE TAIS MET À VOTRE DISPOSITION DE QUELQUE MANIÈRE OU SOUS 
QUELQUE FORME QUE CE SOIT, FAIT FOI DE VOTRE ACCEPTATION DES PRÉSENTES 
MODALITÉS, À MOINS QUE LE FOURNISSEUR DU LOGICIEL NE PRÉSENTE DES MODALITÉS 
DISTINCTES. À DÉFAUT D’ACCEPTER LES MODALITÉS DU PRÉSENT CONTRAT, VOUS NE 
DEVEZ PAS INSTALLER, COPIER NI UTILISER LE PRÉSENT LOGICIEL ET DEVEZ LE RETOURNER 
SANS DÉLAI À L’ENDROIT D’OÙ VOUS L’AVEZ OBTENU, CONFORMÉMENT AUX POLITIQUES DE 
RETOUR EN VIGUEUR. À MOINS D’UNE AUTORISATION CONTRAIRE PAR ÉCRIT DE TAIS, LE 
PRÉSENT LOGICIEL VOUS EST OCTROYÉ À DES FINS EXCLUSIVES DE DISTRIBUTION PAR 
VOIES AUTORISÉES AUX UTILISATEURS. 

1.  Octroi de la licence : Ce logiciel ne vous est pas vendu; vous êtes autorisé à l’utiliser moyennant le 
paiement des frais applicables. TAIS vous accorde le droit individuel, non transférable et non exclusif 
d’utiliser une copie du logiciel fourni en vertu du présent contrat. Vous consentez à ne pas copier le 
logiciel, sauf si nécessaire aux fins d’utilisation sur un seul système TAIS à la fois et dans un même 
endroit. Il vous est strictement interdit de modifier, de traduire, de louer, de reproduire, de distribuer, 
d’imprimer, de sous-louer, de transférer ou de céder ce logiciel, en tout ou en partie, ni de céder les droits 
accordés en vertu du présent contrat à des tiers ou d’enlever les avis, les étiquettes et les marques 
privatifs du logiciel, sauf dans la mesure permise par les lois en vigueur. Vous reconnaissez que la 
violation de l’une ou l’autre de ces interdictions fera un tort irréparable à TAIS et lui fournira les motifs 
nécessaires à l’adoption de mesures injonctives, sans préavis, contre vous et toute autre personne ayant 
le logiciel en sa possession. Toute personne dont la possession du logiciel viole le présent contrat doit, 
sur demande, le rendre à TAIS dans les plus brefs délais. Vous consentez à ne créer aucune œuvre 
dérivée du présent logiciel. En cas de violation du présent contrat par vous ou par des tiers, TAIS se 
réserve le droit de le résilier et de reprendre immédiatement possession du logiciel. L’exécution du 
présent logiciel à d’autres fonctions exige un permis d’exécution valide. 

2.  Propriété intellectuelle : Vous reconnaissez que le titre du logiciel ne vous est nullement cédé, que le 
titre et les droits de pleine propriété du logiciel demeurent la propriété exclusive de TAIS et/ou de ses 
fournisseurs, et vous n’acquerrez aucun droit au logiciel, sauf les droits accordés en vertu de la présente 
licence. Vous ne devez supprimer ni modifier les avis privatifs inscrits sur ou dans ce logiciel. Ce logiciel 
est protégé par les lois américaines sur les brevets, les droits d’auteur et le secret industriel et/ou par 
d’autres lois sur la propriété et des traités internationaux. Tout transfert, utilisation ou reproduction du 
logiciel en violation du présent contrat constitue une violation du droit d’auteur. Sachez que tout transfert, 
usage ou reproduction du logiciel en violation du présent contrat constitue une atteinte volontaire au droit 
d’auteur. 

3.  Interdiction de désosser : Vous acceptez de ne pas essayer de décompiler, de désosser, de modifier, 
de traduire ou de démonter le logiciel, en tout ou en partie. Si vous embauchez des employés ou des 
entrepreneurs, vous devez mettre tout en œuvre pour empêcher que ces employés et entrepreneurs ne 
décompilent, ne désossent, ne modifient, ne traduisent ou ne démontent le logiciel, en tout ou en partie. 
L’inobservation de cette disposition ou d’autres modalités du présent contrat entraînera la résiliation 
automatique de ce dernier et la restitution à TAIS des droits accordés en vertu du présent contrat. 

4.  Garantie limitée : LE PRÉSENT LOGICIEL EST FOURNI « TEL QUEL », SANS GARANTIE DE 
QUELQUE NATURE QUE CE SOIT. DANS LA PLEINE MESURE PERMISE PAR LES LOIS EN 
VIGUEUR, TAIS ET SES FOURNISSEURS DÉSAVOUENT TOUTES LES GARANTIES EXPRESSES 
OU TACITES À L’ÉGARD DU LOGICIEL, NOTAMMENT LES GARANTIES DE NON-VIOLATION DES 
DROITS DE TIERS ET DE CONFORMITÉ À L’AN 2000, ET LA GARANTIE IMPLICITE DE QUALITÉ 
MARCHANDE ET D’ADAPTATION À UN USAGE PARTICULIER. VOUS ACCEPTEZ TOUS LES 

Содержание IP4100 Series

























































































Отзывы: