background image

6

Panel of Remote controller 

Turn on/off 

the oscillating 

button 
Strong wind 

button 

Button of wind volume 

decrease

(Timing time decrease) 

On/ standby button 

Fan speed button 

Button of wind volume increase (Timing 

time increase)

Timing/reserved button 

(AAA battery 1.5V)

Power assembly 

drawing

Please use a manganese or alkaline battery of 

type "AAA" and do not use a non-recyclable 

battery.

Control range of remote controller 

The remote controller control can be normally 

used within 5 meters in front of the product and 

in the left and right angles of 30 degrees. 

Specifications for remote controller buttons 

Icon

Function description

Turn on/Standby 

Turn on/off oscillating to supply wind 

Switch to the normal wind grade by pressing the low→
medium→high→low to cycle 

Switch to the normal wind grade, wind speed and grade are 
increasing;
Switch the time, the timing/reserved time is increasing.
Switch to the normal wind grade, wind speed and grade 
are decreasing;
Switch the time, the timing/reserved time is decreasing.
Turn on/off timing powering off, it will power off 1 hour later; 
Turn on/off reserved powering on, it will power on 1 hour later. 

Turn on/off strong wind 

Press the timing button first, then press the “+、- ”button within 

5 seconds, you can adjust the increase or decrease of the timing time, 
for 4 hours timing range in total(1,2,3,4).

Содержание F-LYA20HKG










Отзывы: