manualshive.com logo in svg

Toshiba e-STUDIO556, Руководство по устранению неисправностей, Страница: 77 / 104

Поделиться
Скачать
Toshiba e-STUDIO556 Скачать руководство пользователя страница 77

6.TROUBLESHOOTING FOR NETWORK CONNECTIONS

Printing Problems (Network Related)    75

6 TROUBLESHOOTING FOR NETWORK CONNECTIONS

IPP print in a Windows operating system environment

Novell print in a NetWare environment

No.

Check...

Yes

No

Corrective Action

1

Are the IP address properties correctly set?

Next Step

Set up the IP address correctly.

2

Is the HTTP server on the equipment enabled?

Next Step

Enable the HTTP server in the HTTP Network 
Service.

3

Is the IPP print correctly set?

Next Step

Set up the IPP print service correctly.

4

Were the proper printer drivers installed?

Next Step

Refer to the 

Software Installation Guide

 to 

install the proper printer drivers.

5

Is the IPP port configured with the correct URL?

Next Step

Refer to the

 Software Installation Guide

 to 

configure the proper port.

6

Can you print to the equipment?

End

See the following section to fix the problem:

 P.60 “Cannot print with the equipment 

(network connection problems)”

No.

Check...

Yes

No

Corrective Action

1

Are the IPX/SPX protocols enabled? Is the correct 
frame type selected?

Next Step

Set up the IPX/SPX correctly.

2

If applicable, did you successfully set up queue-
based print?

Next Step

Set up the NetWare server properly.

3

Did you configure the equipment for a NetWare 
connection?

Next Step

Set up the NetWare network settings correctly.

4

Did you configure the equipment for NetWare 
print service?

Next Step

Set up the NetWare print service correctly.

5

Were the proper printer drivers installed?

Next Step

Refer to the 

Software Installation Guide

 to 

install the proper printer drivers.

6

Is the IPP port configured with the correct URL?

Next Step

Refer to the 

Software Installation Guide

 to 

configure the proper port.

7

Can you see the equipment in Windows Network 
Neighborhood?

Next Step

Check that the SMB protocol is enabled in the 
client computers.

8

Can you print to the equipment?

End

See the following section to fix the problem.

 P.60 “Cannot print with the equipment 

(network connection problems)”

Содержание e-STUDIO556









































































































Отзывы:

Нет отзывов