Toshiba e-STUDIO556 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 104

Toshiba e-STUDIO556 Скачать руководство пользователя страница 100

8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT

98 Regular Maintenance

Regular Maintenance

We recommend that you clean the following portions weekly so that the originals can always be scanned in unsoiled
conditions.



Be careful not to scratch the portions when cleaning them.



When cleaning the surface of the equipment, do not use such organic solvents as thinner or benzine.

-

This could warp the shape of the surface or leave it discolored.

-

When using a chemical cleaning pad to clean it, follow the instructions.

1. Scanning area (surface of the long rectangular glass) / 2. Original glass

Wipe it with the accessory cloth or a soft dry cloth. If there are still stains remaining, wipe clean with a piece of soft
cloth which has been moistened with water and then squeezed well. Do not use liquids other than water (such as
alcohol, organic solvents or neutral detergent).

3. Guide / 4. Platen sheet

Clean the surface as follows depending on the extent of the staining.



Clean it with a soft cloth.



Clean it with a soft cloth lightly moistened with water.



Clean it with a soft cloth lightly moistened with alcohol, and then wipe with a dry cloth.



Clean it with a soft cloth lightly moistened with watered-down neutral detergent, wipe with a cloth moistened with
water, and then wipe with a dry cloth.

3

4

1

2

«
...
98
99
100
101
102
...
»

Содержание e-STUDIO556









































































































Отзывы:

Нет отзывов