manualshive.com logo in svg

Toshiba e-STUDIO2500c, Руководство оператора, Страница: 310 / 414

Поделиться
Скачать
Toshiba e-STUDIO2500c Скачать руководство пользователя страница 310

8 JOB  STATUS

308    Error Code

Error Code

If an error occurs while using the printer, optional Fax, optional Internet Fax or scan, the error 
code is displayed in the status of each log. Take an appropriate action with reference to the fol-
lowing.

Fax / Internet Fax

Error code

Problem

What to do

Fax

0012

Original jam

Clear the jammed original.

0013

Door open

Firmly close the open door.

0020

Power interruption

Check the power interruption report.

0030

Reset

Transmission is cancelled. (The transmission is terminated by 
the jammed printing paper during the Direct Transmission.)

0033

Polling error

Check polling options setup (Security code, etc.), and check if 
the polling document exists.

0042

Memory full

Make sure that there is sufficient memory before making the call 
again.

0050

Line busy

Retry communications.

0053

Security mismatch in 
relay or mailbox trans-
mission

Confirm the remote party’s security code, system password, and 
your setup.

00B0 - 00B5
00C0 - 00C4
00D0 - 00D2
00F0, 00F1

Signal error or line 
condition error

Retry communications. Frequent failures may indicate a phone 
line problem. If possible, move the unit to another line and try 
your communications again.

00E8

HDD error

Retry communications.

Internet Fax

1C10

System access abnor-
mality

Turn the power OFF and then back ON.
Perform the job in error again. If the error still occurs, contact 
your service representative.

1C11

Insufficient memory

When there are running jobs, perform the job in error again after 
the completion of the running jobs. If the error still occurs, turn 
the power OFF and then back ON, and perform the job again.

1C12

Message reception 
error

Turn the power OFF and then back ON.
Perform the job in error again.

1C13

Message transmis-
sion error

Turn the power OFF and then back ON.
Perform the job in error again.

1C14

Invalid parameter

When a template is used, form the template again. If the error 
still occurs, turn the power OFF and then back ON, and perform 
the job again.

1C15

Exceeding file capac-
ity

Ask your administrator to change the “Fragment Page Size” set-
ting for the Internet Fax setting, or reduce the number of pages 
and perform the job again.

1C20

System management 
module access abnor-
mality

Turn the power OFF and then back ON.
Perform the job in error again. If the recovery is still not com-
pleted, contact your service representative.

1C21-1C22

Job control module 
access abnormality

Turn the power OFF and then back ON.
Perform the job in error again. If the recovery is still not com-
pleted, contact your service representative.

1C30-1C33

Disk access error

When there are running jobs, perform the job in error again after 
the completion of the running jobs. If the error still occurs, turn 
the power OFF and then back ON, and perform the job again.

1C40

Image conversion 
abnormality

Turn the power OFF and then back ON. Perform the job in error 
again. If the error still occurs, contact your service representa-
tive.

1C60

HDD full failure during 
processing

Reduce the number of pages of the job in error and perform the 
job again. Check if the server or local disc has a sufficient space 
in disc capacity.

Содержание e-STUDIO2500c































































































































































































































































































































































































































Отзывы:

Нет отзывов