manualshive.com logo in svg

Toshiba DP1600, Руководство по обслуживанию

Toshiba DP1600 - надежный офисный принтер с обширными функциями. Полный сервисный мануал доступен для загрузки бесплатно на manualshive.com. Этот руководство пользователя поможет вам максимально использовать функционал устройства. Скачайте его прямо сейчас!

Поделиться
Скачать
background image

1600/2000/2500 ADJUSTMENT ITEMS

1 - 90

December 2000 © TOSHIBA TEC

8. Settings for the date and time

For details, see chapter 5 of the Operator's Manual.

PROGRAM

0

3

1

0

INITIAL SETUP

DATE & TIME

SETTING

DD-MM-YYYY DAY  HH:MM
15-11-2000 WED  10:10PM

1.10  MAIN PWA replacement procedure

1. Downloading of the MAIN PWA firmware

For details, see chapter 5 of the Service Handbook.

2. Execution of 08-388 mode.  (Reading of the total counter value)

3. RAM Clear with the [1], [3], and [*] keys.

4. Execution of 08-665 mode (05: adjustment clear/08: programming clear)

5. RAM Clear with the [1], [3], and [#] keys.

Power ON

0

8

SET

Power OFF

or

START

3

8

8

Power ON

1

*

Power OFF

3

Warming up

Power ON

1

#

Power OFF

3

Warming up

Power ON

0

2

SET

or

START

1

4

4

Power ON

0

8

SET

Power OFF

or

START

6

5

6

6. Download the scanner PWA firmware, if necessary, after confirming the version of it.

7. Settings for the country code or region code

9. Writing in memory (entering the drum counter value (DRUM COUNTER), long size counter value (A3/

LD) and short size counter value (A4/LT)).

For the setting value, refer to the DRUM UNIT LIST printed before replacing the MAIN PWA.

When the DRUM UNIT LIST is not printed, perform the following setting.

Drum counter value:

Find a remainder by dividing the total counter value (08-351) by the pro-

cess unit life value  (27k or 33k).

Enter the value obtained by multiplying the remainder by 10.

Long size counter value: Enter "0."

Short size counter value: Enter the remainder obtained by dividing the total counter value (08-351)

by the process unit life value (27k or 33k).

For the setting procedures, refer to section 1.2.5 of the Service Handbook.

Setting the country or region code for the
CND and TWD.

CND:

, TWD:

With Fax kit

See the 1.2.6 of the Service Handbook (GD-1060).

Without Fax kit

LT:

A4:

8

6

8

8

6

01/09

Содержание DP1600
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DP1600

Xerox CopyCentre C32 Color Supplementary Manual preview
CopyCentre C32 Color
Бренд: Xerox Страницы: 3
Xerox CopyCentre 232 Reference Manual preview
CopyCentre 232
Бренд: Xerox Страницы: 27
Xerox C123 Copycentre High Capacity Tray Installation Manual preview
C123 Copycentre
Бренд: Xerox Страницы: 3
Xerox C123 Copycentre Scan Manual preview
C123 Copycentre
Бренд: Xerox Страницы: 28
Xerox DocuColor 240 Install Manual preview
DocuColor 240
Бренд: Xerox Страницы: 2
Xerox CopyCentre 232 Supplementary Manual preview
CopyCentre 232
Бренд: Xerox Страницы: 19
Xerox 2830 Product Safety Data Sheet preview
2830
Бренд: Xerox Страницы: 2
Xerox WorkCentre Pro 65 User Manual preview
WorkCentre Pro 65
Бренд: Xerox Страницы: 24
Olivetti DF-650 Service Manual preview
DF-650
Бренд: Olivetti Страницы: 160
Olivetti d-Copia 16 Operation Manual preview
d-Copia 16
Бренд: Olivetti Страницы: 122
Olivetti d-COPIA201D Specifications preview
d-COPIA201D
Бренд: Olivetti Страницы: 2
Canon CLC 1130 Service Manual preview
CLC 1130
Бренд: Canon Страницы: 965
Oki ES3640e MFP Printing Manual preview
ES3640e MFP
Бренд: Oki Страницы: 156

Бренды по названию

Популярные бренды

Загрузить еще бренды