Toshiba AJ65VBTCU-68ADIN Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 106

background image

4 - 6 4 - 6

MELSEC-A

4 SETUP AND PREPARATION BEFORE OPERATION

4.4 Concept of Mode Select Switch Setting (Selection of Remote Device Station Compatible

Version)

The AJ65VBTCU-68ADVN/ADIN must be handled after setting of the remote device
station version according to the configuration of the used CC-Link system.

There are the following remote device stations.

• Ver. 1 remote device station (Ver. 1 compatible slave station)
• Ver. 2 remote device station (Ver. 2 compatible slave station)

Set the remote device station version with the "mode select switch" of the
AJ65VBTCU-68ADVN/ADIN. Refer to Section 4.3 for details of the mode select switch.
In addition, "mode setting" and "station information (station type)" in the network
parameters of GX Developer must be set simultaneously. For details, refer to (2) in this
section and Chapter 5 Programming.

(1) Basic

concept

Use the following as a guideline in setting the remote device station version and
mode select switch.

Mode Select Switch Setting

Guideline for Selection

Ver. 1 remote device station

(Ver. 1 compatible slave station)

Number of occupied stations: 3 stations

In the case of the system where the maximum
number of connected stations of the master station,
including the AJ65VBTCU-68ADVN/ADIN that
occupies 3 stations, does not exceed 64 stations.

Ver. 2 remote device station

(Ver. 2 compatible slave station)

Number of occupied stations: 1 station

In the case of the system where the maximum
number of connected stations of the master station,
including the AJ65VBTCU-68ADVN/ADIN that
occupies 3 stations, exceeds 64 stations. (However,
configure a system where the maximum number of
connected stations of the master station, including
the AJ65VBTCU-68ADVN/ADIN that occupies 1
station, will not exceed 64 stations.)

POINT

In the case of the system where the maximum number of connected stations of the
master station, including the AJ65VBTCU-68ADVN/ADIN that occupies 3 stations,
does not exceed 64 stations, set and use the ver. 1 remote device station (ver. 1
compatible slave station). It is not particularly necessary to set and use the ver. 2
remote device station (ver. 2 compatible slave station).

«
...
44
45
46
47
48
...
»

Содержание AJ65VBTCU-68ADIN











































































































Отзывы:

Нет отзывов

Похожие инструкции для AJ65VBTCU-68ADIN

Бренд: Waterway Страницы: 16

Бренд: 3M Страницы: 34

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: LAS Страницы: 6

Бренд: Parkside Страницы: 65

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

Бренд: Universal Remote Страницы: 20

Бренд: East Coast Datacom Страницы: 14

Waukesha Cherry-Burrell D4 Series

Бренд: SPX FLOW Страницы: 34

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Devicenet R7F4HD-DAC32C

Бренд: M-system Страницы: 9

Бренд: Universal Remote Страницы: 10

Бренд: D+H Страницы: 4

Бренд: Genius Страницы: 52

Бренд: Casablanca Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды