Toshiba AJ65VBTCU-68ADIN Скачать руководство пользователя страница 42

Страница: 42 / 106

4 - 2 4 - 2

MELSEC-A

4 SETUP AND PREPARATION BEFORE OPERATION

CAUTION

Dispose of the product as industrial waste.
Use the module in the environment indicated in the general specifications given in

this manual.
Not doing so can cause an electric shock, fire, malfunction, product damage or
deterioration.

Securely fix the module to a DIN rail or securely fix it with the CC-Link connector

type fitting.
Not doing so can cause a drop or malfunction.

Mount or dismount the module to or from an enclosure after switching power off

externally in all phases. Not doing so can cause the module to fail or malfunction.

Always make sure to touch the grounded metal to discharge the electricity charged

in the body, etc., before touching the module.
Failure to do so may cause a failure or malfunctions of the module.

(1) When using the DIN rail adapter, install the DIN rail by making sure of the

following:
(a) Applicable DIN rail models (conforming to the JIS C 2812)

TH35-7.5Fe
TH35-7.5Al

(b) DIN rail installation screw interval

When installing the DIN rail, tighten the screws with less than 200mm (7.87
inch) pitches.

(2) As the CC-Link connector type metal installation fitting, use the narrow-width type

(width 41)-dedicated fitting.

(a) CC-Link connector type metal installation fitting model

A6PLT-J65V1

(3) Refer to the Master Module user's manual for specification, and manufacturers of

supported cables for the use with AJ65VBTCU-68ADVN/ADIN.

Содержание AJ65VBTCU-68ADIN











































































































Результаты поиска

Содержание AJ65VBTCU-68ADIN

Отзывы:

Похожие инструкции для AJ65VBTCU-68ADIN

Бренды по названию

Популярные бренды

Toshiba AJ65VBTCU-68ADIN, Руководство пользователя

Результаты поиска

Содержание AJ65VBTCU-68ADIN

Отзывы:

Похожие инструкции для AJ65VBTCU-68ADIN

Бренды по названию

Популярные бренды