14
Getting started
Note:
After the
Auto scan
, the TV may have scanned identical
channels being broadcast from different transmitters. You can
verify this by
previewing
those channels in the
Channel List
with identical logical numbers and check on their physical
channel numbers (
-
page 30). If you do find channels with
the same logical channel numbers but different physical
channel numbers, it is recommended that you skip these
duplicate channels and keep only one channel with the best
signal strength as indicated by the SNR indicator in the I-Plate
(
-
page 16) display.
Manual scan
- digital only -
If there were any missing channel after
Auto Scan
, these
channels might be found by using
Manual Scan
described in
this section. Also, if you do not live in Australia, you must use
Manual Scan
to scan those channels in your country.
1
From the
SCAN
menu, press
or
to select
Manual
Scan
, then press
Q
.
2
Enter password using the
Number
buttons or press 0000
(which is the default password), then
Manual Scan
will
appear.
3
Press
or
to select the item you wish to adjust. For
Australia, to adjust
Frequency
, you may refer to the
latest channel table from local dealer. And the
Bandwidth
is 7MHz and
Priority
should be set to
HIGH
. Then press
or
to select
Start Scan
and
press
Q
to start scanning.
4
If scanning was successful,
Get Channel Success
appeared for 2 seconds. Repeat to scan other channels as
necessary.
5
If scanning was unsuccessful,
Timeout Error
appeared.
At this point you can rescan the signal or refer to the
Signal Level
bar and
Quality
for aligning the direction
of the antenna to get the signal. Refer to your antenna
installer if problem persists.
Notes:
•
Signal level
refers to the input Radio Frequency (RF) signal
strength as perceived by the TV. Note that too strong signal
may cause erroneous readings. If you use an antenna
booster and find that you still get a low signal level, your
booster gain may be set too high. In this case, adjust the
gain accordingly. You may also see the
No Signal
on the
screen when the signal level is low.
•
Quality
refers to the quality of the received digital signal. A
high value of quality means that there are few errors in the
signal. In the same way, a low value of quality implies that
there are a large number of errors in the signal, which may
cause distortions in video and audio.
Programming channels automatically
- analog only -
First, use the Auto tuning function to preset all the active
channels in your area automatically. Then, arrange the preset
channels with the Manual tuning function so that you can tune
into only desired channels.
1
Press
M
, then press
or
to display the
SET UP
menu.
2
Press
or
to select
Auto tuning
.
3
Press
Q
to display the
Auto tuning
menu.
4
Press
Q
to start the automatic search.
The search will begin for all available stations.
The slide bar will move along the line as the search
progresses.
If you make a mistake, simply repeat steps 1-4 to start
again from the beginning.
5
When the automatic search is completed, the TV will
automatically return to the first program position.
6
Press
or
to view the programmed position.
Note:
When you preset the program channel which sound of
broadcast transmission system adopts “M” system, the sound
system may not be tuned correctly if the radio waves transmit
badly. At that time, preset the channel by
Manual tuning
.
Channel No.
Bandwidth
Priority
Signal Level
Quality
100%
70%
Frequency
Start Scan
SNR: 20dB
Scanning...
6
1775000 KHz
HIGH
7 MHz
Manual S
c
an
Ba
c
k Wat
c
h TV
Sele
c
t Fun
c
tion
ANT ATT
Manual tuning
OK
AV connection
OK
Picture position
OK
Auto tuning
OK
Language
SET UP
MENU
Back Watch
TV
EXIT
English
Off
MENU
Back
Watch TV
EXIT
Auto tuning
EXIT for no change.
Press OK key to start.
!
Searching
Stop
Pos
:2
Auto tuning
EXIT
Содержание 32C2000A
Страница 43: ...43 Note ...
Страница 44: ......
