37
XF550U (E/F) Web 213:276
Chapter 5: Setting up your TV
3
Open the
Terrestrial
menu, highlight
Channel
Program
to bring up the
Start
, and press
T
again to
begin channel programming.
The TV will automatically cycle through all the antenna
channels, and store all active channels in the channel
memory. While the TV is cycling through the channels,
the message “Scanning channels, please wait” appears (as
shown above).
4
To cancel channel programming, press
O
on the remote
control (or highlight
Cancel
in the on-screen display and
press
T
).
When channel programming is finished, press
<
or
,
to
view the programmed channels.
Manually adding and deleting channels
in the channel memory
After automatically programming channels into the channel
memory, you can manually add or delete individual channels.
To add or delete channels in the channel memory:
1
From the
Setup
menu, highlight
Installation
and press
T
. A new set of
Installation
menu icons will appear.
2
Open the
Terrestrial
menu, highlight
Channel Add/
Delete
, and then press
T
.
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number you
want to add, and then press
T
to check the box.
To manually add digital subchannels on a physical
channel:
Use the Channel Numbers and the Dash (
=
) on the remote
control to enter the channel number (for example, 56–1).
If the channel is found, the number will be added to the list and
the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you
want to remove, and then press
T
to uncheck the box.
To save your new settings:
Highlight
Done
and press
T
.
Note:
A video preview of the currently highlighted channel is
provided to assist you in adding/deleting channels.
To revert to your original settings:
Highlight
Cancel
and press
T
before saving.
To remove all channels from the channel memory:
Highlight
Reset
and press
T
, and then highlight
Done
and
press
T
.
To remove encrypted channels from the channel
memory:
If an encrypted channel is accidentally added to the channel list
by programming channels, you can remove the unwanted
encrypted (non-viewable) channel while you are channel
surfing. When you tune into an encrypted channel, the
following message will appear.
Press
1
while the message is on the screen to remove the
unnecessary channel from the channel list.
Setting the Auto Input feature
This feature allows you to change TV inputs using the
MODE
SELECT
buttons—
TV, CABLE/SAT, HD DVD, DVD,
VCR/PVR
—on the remote control. Once an input has been set
for a specific
MODE SELECT
button, the TV will
automatically switch to the input when you press and hold the
MODE SELECT
button for 2 seconds.
Auto Input settings options for each
MODE SELECT
button
are shown below.
•
TV
: ANT/CABLE
•
CABLE/SAT
: ANT/CABLE, Video 1, Video 2,
ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2,
HDMI 3, PC
•
HD DVD
: Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, PC
•
DVD
: Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2, HDMI 3, PC
•
VCR/PVR
: ANT/CABLE, Video 1, Video 2,
ColorStream HD1, ColorStream HD2, HDMI 1, HDMI 2,
HDMI 3, PC
Note:
The TV mode select button will be restricted to the ANT/
CABLE input.
To set the Auto Input:
1
From the
Preferences
menu, highlight
Auto Input
and
press
T
.
ANT/CABLE Cable
Scanning channels, please wait ...
Number of Channels Found - 52
Scanning Analog Channels
Found Channel - 55
Cancel
5%
Digital Channel Is Encrypted - Press 1 on remote to remove channel
(continued)
40XF550U_EN.book Page 37 Monday, March 17, 2008 2:07 PM
