Toro Z Master G3 Скачать руководство пользователя страница 63

Страница: 63 / 68

B. Run the engine to distribute conditioned fuel

through the fuel system (5 minutes).

C. Stop the engine, allow it to cool, and drain the

fuel tank; refer to Servicing the Fuel Tank in the
Maintenance Section.

D. Restart the engine and run it until it stops.

E. Dispose of fuel properly. Recycle as per local

codes.

Important:

Do not store

stabilizer/conditioned fuel over 90 days.

13. Check and tighten all bolts, nuts, and screws. Repair

or replace any part that is damaged.

14. Paint all scratched or bare metal surfaces. Paint is

available from your Authorized Service Dealer.

15. Store the machine in a clean, dry garage or storage

area. Remove the key from the ignition switch and
keep it out of reach of children or other unauthorized
users. Cover the machine to protect it and keep it
clean.

Содержание Z Master G3





































































Результаты поиска

Содержание Z Master G3

Отзывы:

Похожие инструкции для Z Master G3

Бренды по названию

Популярные бренды

Toro Z Master G3, Руководство оператора

Результаты поиска

Содержание Z Master G3

Отзывы:

Похожие инструкции для Z Master G3

Бренды по названию

Популярные бренды