Toro Z Master G3 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

Toro Z Master G3 Скачать руководство пользователя страница 37

Servicing the Spark Plug

Service Interval:

Every 100 hours

Make sure the air gap between the center and side
electrodes is correct before installing the spark plug.
Use a spark plug wrench for removing and installing
the spark plug(s) and a gapping tool/feeler gauge to
check and adjust the air gap. Install a new spark plug(s)
if necessary.

Type of Spark Plug:

NGK

®

BPR4ES or equivalent

Air Gap:

0.030 inch (0.75 mm)

Removing the Spark Plug

1. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

2. Disengage the PTO, move the motion control levers

to the neutral locked position and set the parking
brake.

3. Locate and remove the spark plugs (Figure 50).

g015124

Figure 50

Checking the Spark Plug

Important:

Never clean the spark plug(s). Always

replace the spark plug(s) when it has: a black
coating, worn electrodes, an oily film, or cracks.

If you see light brown or gray on the insulator, the
engine is operating properly. A black coating on the
insulator usually means the air cleaner is dirty.

Set the gap to 0.030 inches (0.76 mm).

G008794

1

2

Figure 51

Installing the Spark Plug

Tighten the spark plug(s) to 16 ft.-lb (22 N-m).

Figure 52

37

«
...
35
36
37
38
39
...
»

Содержание Z Master G3





































































Отзывы:

Нет отзывов