background image

6

Checking the Torque of the
Wheel Lug Nuts

No Parts Required

Procedure

Before you start the engine and use the machine, check the
wheel lug nut torque; refer to Checking the Wheel Lug Nuts
in the

Operator's Manual

7

Installing the Battery

Parts needed for this procedure:

2

Wing nut (1/4 inch)

Procedure

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known to the State of California

to cause cancer and reproductive harm.

Wash hands after handling.

CAUTION

Battery electrolyte contains sulfuric acid, which is
poisonous and can cause severe burns. Swallowing
electrolyte can be fatal or if it touches skin can
cause severe burns.

Wear safety glasses to shield eyes, and rubber
gloves to protect skin and clothing when
handling electrolyte.

Do not swallow electrolyte.

In the event of an accident, flush with water and
call a doctor immediately.

WARNING

If the ignition is in the On position there is potential
for sparks and engagement of components. Sparks
could cause an explosion or moving parts could
accidentally engage causing personal injury.

Be sure ignition switch is in the Off position before
charging the battery.

Locate the battery-mounting hardware and install the negative
battery cable. Refer to Installing the Battery in the

Operator's

Manual.

Note:

If the positive cable is also disconnected, connect the

positive (red) cable to the positive battery terminal first, then
the negative (black) cable to the negative battery terminal.
Slip insulator boot over the positive terminal.

Note:

If time does not permit charging the battery, or if

charging equipment is not available, connect the negative
battery cable and run the vehicle continuously for 20 to 30
minutes to sufficiently charge the battery.

8

Charging the Battery

No Parts Required

Procedure

WARNING

Charging the battery produces gasses that can
explode and cause serious injury.

Keep cigarettes, sparks and flames away from
the battery.

Make sure that the ignition switch is off.

Ventilate when charging or using the battery in
an enclosed space.

Important:

Do not run the machine with the battery

disconnected; electrical damage may occur to the
engine.

Charge the battery. Refer to the

Operator's Manual

for

instructions.

8

 

Содержание Z MASTER 74310













Отзывы: