Toro Workman MDE 2008 Скачать руководство пользователя страница 14

Страница: 14 / 130

Rev. A

Workman MDE

Page 2 -- 4

Product Records and Maintenance

Standard Torque for Dry, Zinc Plated and Steel Fasteners (Inch Series)

Thread Size

Grade 1, 5 &

8 with Thin

Height Nuts

SAE Grade 1 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 2 or Stronger Nuts)

SAE Grade 5 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 2 or Stronger Nuts)

SAE Grade 8 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 5 or Stronger Nuts)

in--lb

N--cm

in--lb

N--cm

in--lb

N--cm

# 6 -- 32 UNC

10 + 2

13 + 2

147 + 23

15 + 2

169 + 23

23 + 3

262 + 34

# 6 -- 40 UNF

10 + 2

13 + 2

147 + 23

17 + 2

192 + 23

25 + 3

282 + 34

# 8 -- 32 UNC

13 + 2

25 + 5

282 + 30

29 + 3

328 + 34

41 + 5

463 + 56

# 8 -- 36 UNF

13 + 2

25 + 5

282 + 30

31 + 4

350 + 45

43 + 5

486 + 56

# 10 -- 24 UNC

18 + 2

30 + 5

339 + 56

42 + 5

475 + 56

60 + 6

678 + 68

# 10 -- 32 UNF

18 + 2

30 + 5

339 + 56

48 + 5

542 + 56

68 + 7

768 + 79

1/4 -- 20 UNC

48 + 7

53 + 7

599 + 79

100 + 10

1130 + 113

140 + 15

1582 + 169

1/4 -- 28 UNF

53 + 7

65 + 10

734 + 113

115 + 12

1299 + 136

160 + 17

1808 + 192

5/16 -- 18 UNC

115 + 15

105 + 15

1186 + 169

200 + 25

2260 + 282

300 + 30

3390 + 339

5/16 -- 24 UNF

138 + 17

128 + 17

1446 + 192

225 + 25

2542 + 282

325 + 33

3672 + 373

ft--lb

N--m

ft--lb

N--m

ft--lb

N--m

3/8 -- 16 UNC

16 + 2

22 + 3

30 + 3

41 + 4

43 + 5

58 + 7

3/8 -- 24 UNF

17 + 2

18 + 2

24 + 3

35 + 4

47 + 5

50 + 6

68 + 8

7/16 -- 14 UNC

27 + 3

37 + 4

50 + 5

68 + 7

70 + 7

95 + 9

7/16 -- 20 UNF

29 + 3

39 + 4

55 + 6

75 + 8

77 + 8

104 + 11

1/2 -- 13 UNC

30 + 3

48 + 7

65 + 9

75 + 8

102 + 11

105 + 11

142 + 15

1/2 -- 20 UNF

32 + 4

53 + 7

72 + 9

85 + 9

115 + 12

120 + 12

163 + 16

5/8 -- 11 UNC

65 + 10

88 + 12

119 + 16

150 + 15

203 + 20

210 + 21

285 + 28

5/8 -- 18 UNF

75 + 10

95 + 15

129 + 20

170 + 18

230 + 24

240 + 24

325 + 33

3/4 -- 10 UNC

93 + 12

140 + 20

190 + 27

265 + 27

359 + 37

375 + 38

508 + 52

3/4 -- 16 UNF

115 + 15

165 + 25

224 + 34

300 + 30

407 + 41

420 + 43

569 + 58

7/8 -- 9 UNC

140 + 20

225 + 25

305 + 34

430 + 45

583 + 61

600 + 60

813 + 81

7/8 -- 14 UNF

155 + 25

260 + 30

353 + 41

475 + 48

644 + 65

667 + 66

904 + 89

NOTE:

Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

engine oil or thread sealant such as Loctite.

NOTE:

Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

NOTE:

The nominal torque values listed above for

Grade 5 and 8 fasteners are based on 75% of the mini-

mum proof load specified in SAE J429. The tolerance is

approxi 10% of the nominal torque value. Thin

height nuts include jam nuts.

Содержание Workman MDE 2008



































































































































Результаты поиска

Содержание Workman MDE 2008

Отзывы:

Похожие инструкции для Workman MDE 2008

Бренды по названию

Популярные бренды

Toro Workman MDE 2008, Руководство по обслуживанию

Результаты поиска

Содержание Workman MDE 2008

Отзывы:

Похожие инструкции для Workman MDE 2008

Бренды по названию

Популярные бренды