background image

Form No. 3385-426 Rev A

Ultra Sonic Boom

Leveling Kit

2013 and After Multi-Pro 5800, 1750 and WM Turf Sprayers

Model No. 41219—Serial No. 314000001 and Up

Installation Instructions

This attachment maintains consistent distances from the boom nozzles to the ground when
spraying over uneven surfaces and is intended to be used by professional, hired operators in
commercial applications. It is primarily designed for spraying golf course applications, parks,
sports fields, and on commercial grounds. It is designed to only be used in conjunction with
machines designated by the manufacturer.

This product complies with all relevant European directives. For details, please see the
separate product specific Declaration of Conformity (DOC) sheet.

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

Use of this product may cause exposure to

chemicals known to the State of California

to cause cancer, birth defects, or other

reproductive harm.

© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3385-426* A

Содержание Ultra Sonic Boom 41219

















Отзывы: