Toro Recycler 21762 Скачать руководство пользователя страница 25

Страница: 25 / 28

Adjusting the Self-Propel
Drive

For Self-Propel-Drive Models Only

Whenever you install a new self-propel cable or if
the self-propel drive is out of adjustment, adjust the
self-propel drive.

Turn the adjustment nut counterclockwise to
loosen the cable adjustment (

Figure 34

g269307

Figure 34

Handle (left side)

Turn the nut clockwise to
tighten the adjustment.

Adjustment nut

Turn the nut
counterclockwise to
loosen the adjustment.

Self-propel-drive cable

Adjust the tension on the cable (

Figure 34

) by

pulling it back or pushing it forward and holding
that position.

Note:

Push the cable toward the engine to

increase the traction; pull the cable away from
the engine to decrease the traction.

Turn the adjustment nut clockwise to tighten the
cable adjustment.

Note:

Tighten the nut firmly with a socket or

wrench.

Содержание Recycler 21762





























Результаты поиска

Содержание Recycler 21762

Отзывы:

Похожие инструкции для Recycler 21762

Бренды по названию

Популярные бренды

Toro Recycler 21762, Руководство оператора

Результаты поиска

Содержание Recycler 21762

Отзывы:

Похожие инструкции для Recycler 21762

Бренды по названию

Популярные бренды