background image

27

F

–20

0

20

40

60

80

100

5

C

–30

5

–20

–10

0

10

20

30

40

USE THESE SAE VISCOSITY OILS

32

5W–20, 5W–30

10W–30

Checking Oil Level

1. Park the machine on a level surface, disengage the

power take off (PTO), set the parking brake, and turn
the engine off.

2. Clean around the oil dipstick (Fig. 33) so dirt cannot

fall into the filler hole and damage the engine.

3. Unscrew the oil dipstick and wipe the metal end clean

(Fig. 33).

4. Slide the oil dipstick fully into the filler tube, do not

thread onto tube (Fig. 33). Pull the dipstick out and look
at the metal end. If oil level is low, slowly pour only
enough oil into the filler tube to raise the level to the
full mark.

Important

 

Do not overfill the crankcase with oil

because the engine may be damaged.

1

2

3

Figure 33

1.

Oil dipstick

2.

Metal end

3.

Filler tube

Changing the Oil

1. Start the engine and let it run five minutes. This warms

the oil so it drains better.

2. Park the machine so that the drain side is slightly lower

than the opposite side to assure the oil drains
completely. Then disengage the power take off (PTO),
set the parking brake, and turn the engine off.

3. Place a pan below the oil drain. Remove the oil drain

cap (Fig. 34).

4. When oil has drained completely, install the oil drain

cap.

Note: Dispose of the used oil at a certified recycling center.

1

m–4758

Figure 34

1.

Oil drain cap

5. Slowly pour approximately 80% of the specified oil on

page 26, into the filler tube (Fig. 33). Now check the oil
level; refer to Checking Oil Level, page 27. Slowly add
additional oil to bring to full mark on dipstick.

Changing the Oil Filter

Service Interval/Specification

Replace the oil filter every 200 hours or every other oil
change.

Note: Change oil filter more frequently when operating
conditions are extremely dusty or sandy.

1. Drain the oil from the engine; refer to

Changing/Draining Oil, page 27.

2. Remove the old filter and wipe the filter adapter

(Fig. 35) gasket surface.

3. Apply a thin coat of new oil to the rubber gasket on the

replacement filter (Fig. 35).

Содержание ProLine 30197









































Отзывы: