background image

Form No. 3414-446 Rev A

HoverPro

®

400 Machine

Model No. 02615—Serial No. 400000000 and Up

Operator's Manual

Introduction

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical

or chemicals known to the State of

California to cause cancer, birth defects,

or reproductive harm.

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

It is a violation of California Public Resource Code
Section 4442 or 4443 to use or operate the engine on
any forest-covered, brush-covered, or grass-covered
land unless the engine is equipped with a spark
arrester, as defined in Section 4442, maintained in
effective working order or the engine is constructed,
equipped, and maintained for the prevention of fire.

This machine does not come equipped with a
spark arrester standard. You must install the
spark arrester kit before operating this machine in
California.

This spark ignition system complies with Canadian
ICES-002.

The enclosed

Engine Owner's Manual

is

supplied for information regarding the US
Environmental Protection Agency (EPA) and
the California Emission Control Regulation of
emission systems, maintenance, and warranty.
Replacements may be ordered through the engine
manufacturer.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely. Keep for
future reference.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service

Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product.

1

g017415

g017415

Figure 1

1.

Model and serial number plate

Write the product model and serial numbers in the
space below:

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

1.

Safety-alert symbol

© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the UK

All Rights Reserved

*3414-446* A

 

Содержание HoverPro 400





















Отзывы: