Toro Groundsmaster 3500 30807, Руководство по обслуживанию

Страница: 131 / 283

Groundsmaster 3500 Hydraulic System Page 5 − 73
Filtering Closed−Loop Traction Circuit
Filtering of a closed−loop hydraulic system after a major
component failure (e.g. traction (piston) pump or wheel
motor) is a requirement to prevent debris from transmit-
ting throughout the system. If a closed−loop hydraulic
system filtering tool is not used (to ensure system clean-
liness) repeat failures and subsequent damage to other
hydraulic components in the system will occur. To effec-
tively remove contamination from closed−loop traction
circuit, use of the Toro high flow hydraulic filter and hy-
draulic hose kit are recommended (see Special Tools in
this chapter).
1. Park machine on a level surface, stop engine and re-
move key from ignition switch.
WARNING
Before jacking up the machine, review and follow
Jacking Instructions in Chapter 1 − Safety.
2. Raise and support machine so all wheels are off the
ground.
NOTE: If a wheel motor was replaced, install high flow
filter to the inlet (when traveling forward) of new wheel
motor instead of to the inlet (when traveling forward) of
the traction pump. This will prevent system contamina-
tion from entering and damaging the new motor.
3. Thoroughly clean junction of hydraulic hose and
lower fitting on rear wheel motor (Fig. 46). Disconnect
hose from lower fitting on wheel motor.
4. Connect Toro high flow hydraulic filter in series be-
tween wheel motor fitting and disconnected hose. Use
hydraulic hose kit (see Special Tools in this chapter) to
connect filter to machine. Make sure that fitting and hose
connections are properly tightened.
IMPORTANT: Use only hydraulic fluids specified in
Operator’s Manual. Other fluids could cause system
damage.
5. After installing high flow filter to machine, check and
fill hydraulic reservoir with new hydraulic oil as required.
6. Sit in the operator’s seat and start engine. Run en-
gine at low idle speed and check for any hydraulic leak-
age from filter and hose connections. Correct any leaks
before proceeding.
IMPORTANT: While engaging the traction circuit,
monitor the high flow hydraulic filter indicator. If the
indicator should show red, either reduce traction
pedal setting or reduce engine speed to decrease
hydraulic flow through the filter.
7. With engine running at low idle speed, slowly de-
press the forward traction pedal to the full forward posi-
tion to allow flow through the traction circuit and high
flow filter. Keep traction circuit engaged for five (5) min-
utes while gradually increasing both forward pressure
on traction pedal and engine speed. Monitor filter indica-
tor to make sure that green color is showing during op-
eration.
8. With engine running at high idle speed and traction
pedal moved to the forward direction, periodically apply
brakes to increase pressure in traction circuit. While
monitoring filter indicator, continue this process for an
additional five (5) minutes.
IMPORTANT: If using a filter that is not the bi−direc-
tional Toro high flow filter, do not press the traction
pedal in the reverse direction. If flow is reversed
when using a filter that is not bi−directional, debris
from the filter will re−enter the traction circuit.
9. With engine running at high idle speed, alternately
move traction pedal from forward to reverse. While mon-
itoring filter indicator, continue this process for an addi-
tional five (5) minutes.
10.Shut engine off and remove key from ignition switch.
11. Remove high flow hydraulic filter and hydraulic hose
kit from machine. Reconnect hydraulic hose to rear
wheel motor fitting. Make sure to properly tighten hose
(see Hydraulic Hose and Tube Installation in the Gener-
al Information section of this chapter).
12.Lower machine to ground.
13.Check oil level in hydraulic reservoir and add correct
oil if necessary.
Figure 46
1. Rear wheel motor 2. Lower fitting
FRONT
RIGHT
1
2
Hydraulic
System