background image

This product contain a modular approval with FCC ID MCQ-XBPSX 

and IC 1846A-XBPSX.
This equipment has been tested and found to comply with the limits for a 

Class A digital device, pursuant to part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference 

when the equipment is operated in a commercial environment. This 

equipment generates, uses, and can radiate radio frequency energy and, 

if not installed and used in accordance with the instruction manual, may 

cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in 

which case the user will be required to correct the interference at his own 

expense.

This device contains licence-exempt transmitter(s)/receiver(s) that comply 

with innovation, Science, and Economic development Canada’s licence-

exempt RSS(s). Operation is subject to the following two conditions: 

(1) this device may not cause interference, and 
(2) This device must accept any interference, including interference 

that may cause undesired operation of the device.

L’émetteur/recepteur exempt de license contenu dans le présent appareil 

est conforme aux CNR d’innovation, Science et Dévellopement 

économique Canada applicables aux appareils radio exempts de licence. 

L’exploitation est autorisée aux deux condtions suivantes: 

(1) l’appareil ne doit pas produire de brouillage, et 
(2) l’appareil doit accepter tout brouillage radioélectrique subi, même 

si le brouillage est suceptible d’en compromettre le fonctionnement.

This device complies with FCC and ISED RF radiation exposure limits 

set forth for genral population. This device must be installed to provide a 

separation distance of at least 20cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter.
Le present appareil est conforme aux niveaux limites d’exigences 

d’exposition RF aux personnes définies par ISDE. L’appareil doit être 

installé afin d’offrir une distance de séparation d’au moins 20cm avec 

les personnes et ne doit pas être installé à proximité ou être utilisé en 

conjonction avec une autre antenne ou un autre émetteur.

FCC and IC Statement

5825 Jasmine Street

Riverside, CA 92504

800-777-1477

[email protected]

©2021 The Toro Company  • www.toro.com  • Patents: www.ttcopats.com

Part Number 373-1071 Rev. A

WARNING: Cancer and Reproductive harm – www.P65Warnings.ca.gov. 

For more information, please visit www.toro.com/CAProp65.

!

Содержание DXi










Отзывы: