Toro CCR 2450 GTS Series Скачать руководство пользователя страница 20

Страница: 20 / 28

m-3215

Figure 26

0.030 in. (0.76 mm)

10. Install the spark plug by hand and then torque it to

15 ft-lb (20.4 N

m). If you do not have a torque wrench,

tighten the plug firmly.

11. Connect the wire to the spark plug.

12. Install the control panel.

13. Insert the key in the switch.

Replacing the Drive Belt

Inspect the drive belt before each season, and replace it if it
is worn or damaged.

1. Stop the engine and wait for all moving parts to stop.

2. Remove the key from the switch.

3. Disconnect the wire from the spark plug. Refer to steps

3 through 5 of Replacing the Spark Plug on page 19.

4. Remove the fasteners that secure the drive belt cover to

the snowthrower frame (Fig. 27). Set the drive belt
cover aside.

m-5534

Figure 27

Drive belt cover

Nut (2)

Washer

Short self-tapping
screw (2)

Long self-tapping screw

Bolt (2)

5. Pull up on the idler pulley and remove the old drive belt

from the rotor pulley, the brake arm assembly, and the
engine pulley (Fig. 28).

626

Figure 28

Engine pulley

Idler pulley

Roller

Brake arm assembly

Rotor pulley

Belt guide

6. Loop the new drive belt around the engine pulley, under

the idler pulley, over the roller, through the brake
assembly, and around the rotor pulley (Fig. 28).

Important

The drive belt must be on top of the roller as

shown in Figure 28.

7. Install the drive belt cover. Tighten the fasteners

securely, but do not overtighten.

8. Connect the wire to the spark plug.

9. Install the control panel.

10. Insert the key in the switch.

Emptying the Fuel Tank

1. Stop the engine and wait for all moving parts to stop.

2. Remove the key from the switch.

Содержание CCR 2450 GTS Series





























Результаты поиска

Содержание CCR 2450 GTS Series

Отзывы:

Похожие инструкции для CCR 2450 GTS Series

Бренды по названию

Популярные бренды

Toro CCR 2450 GTS Series, Руководство оператора

Результаты поиска

Содержание CCR 2450 GTS Series

Отзывы:

Похожие инструкции для CCR 2450 GTS Series

Бренды по названию

Популярные бренды