Toro 405500000 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 36

Toro 405500000 Скачать руководство пользователя страница 4

Safety

General Safety

•

Read and understand the contents of this
Operator’s Manual before starting the engine.

•

Do not operate the machine without all guards
and other safety protective devices in place and
functioning properly on the machine.

•

Park the machine on a level surface, lower the
hopper, shut off the engine, and remove the key
before leaving the operating position.

•

Keep your hands and feet away from moving
parts. If possible, do not make adjustments with
the engine running.

Improperly using or maintaining the machine can
result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety-alert symbol (

), which

means

Caution

,

Warning

, or

Danger

—personal

safety instruction. Failure to comply with the
instruction may result in personal injury or death.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

125-4961

decal125-4961

125–4961

1.

Reverse

decal125-4964

125–4964

1.

Read the

Operator’s Manual

for oil information.

decal125-4959

125–4959

1.

Crushing hazard—never place your head under the dump
trailer.

125-4960

decal125-4960

125–4960

1.

Forward

4

«
...
2
3
4
5
6
...
»

Содержание 405500000





































Отзывы:

Нет отзывов