Toro 30696 Скачать руководство пользователя страница 48

Landscape

Contractor

Equipment (LCE)

The Toro Total Coverage Guarantee

A Limited Warranty

Conditions and Products Covered

The Toro® Company and its afliate, Toro Warranty Company, pursuant to an

agreement between them, jointly promise to repair the listed Toro Products if

defective in materials or workmanship. The following time periods apply from

the date of purchase:
This warranty applies to:

ProLine Mid-Size Mowers and Attachments

1 year

Z Master Mid-Mount ZRTs and Attachments

1 year

Components

Warranty Period

Traction Unit Frame and Carrier Frame

2 year

All Spindles

3 years Parts

2 years Labor

Engines* and /Hydraulic System

2 years

Deck Shells (34

-72

)

2 years

Z500 Series Electric Clutch

2 years

Remaining Components

1 year

*Some engines used on Toro LCE Products are warranted by the engine manufacturer.

This warranty includes the cost of parts and labor, but you must pay

transportation costs.

Instructions for Obtaining Warranty Service

If you think that your Toro Product contains a defect in materials or

workmanship, follow this procedure:
1.

Contact any Toro Authorized or Master Service Dealer to arrange service at

their dealership. To locate a dealer convenient to you, access our website at

www.Toro.com. You may also call our Toro Customer Care Department

toll free at 888–865–5676 (U.S. Customers) or 888–865–5691 (Canada

customers).

2.

Bring the product and your proof of purchase (sales receipt) to the Service

Dealer.

If for any reason you are dissatised with the Service Dealer’s analysis or with

the assistance provided, contact us at:

LCB Customer Service Department

Toro Warranty Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Owner Responsibilities

You must maintain your Toro Product by following the maintenance procedures

described in the operator’s manual. Such routine maintenance, whether

performed by a dealer or by you, is at your expense.

Items and Conditions Not Covered

There is no other express warranty except for special emission system coverage

on some products. This express warranty does not cover the following:

Cost of regular maintenance service or parts, such as lters, fuel, lubricants,

tune-up parts, blade sharpening, brake and clutch adjustments.

Any product or part which has been altered or misused or required

replacement or repair due to normal wear, accidents, or lack of proper

maintenance.

Repairs necessary due to improper fuel, contaminants in the fuel system, or

failure to properly prepare the fuel system prior to any period of non-use

over three months.

Pickup and delivery charges.

General Conditions

All repairs covered by this warranty must be performed by an Authorized Toro

Service Dealer using Toro approved replacement parts.

Neither The Toro® Company nor Toro Warranty Company is liable for

indirect, incidental or consequential damages in connection with the

use of the Toro Products covered by this warranty, including any

cost or expense of providing substitute equipment or service during

reasonable periods of malfunction or non-use pending completion

of repairs under this warranty.
Some states do not allow exclusions of incidental or consequential

damages, or limitations on how long an implied warranty lasts, so

the above exclusions and limitations may not apply to you.
All implied warranties of merchantability (that the product is t

for ordinary use) and tness for use (that the product is t for

a particular purpose) are limited to the duration of the express

warranty.
This warranty gives you specic legal rights, and you may also have

other rights which vary from state to state.

Countries Other than the United States or Canada

Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee

policies for your country, province, or state. If for any reason you are dissatised with your Distributor’s service or have difculty obtaining guarantee information,

contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.

374-0037 Rev F

Содержание 30696

















































Отзывы: