Toro 30659 LT-F3000 Скачать руководство пользователя страница 19

Страница: 19 / 60

Ignition Switch

= Engine off

= Engine run/auxiliary on

= Engine preheat

III

= Engine start

WARNING

If you leave the key in the ignition switch, someone
could accidentally start the engine and seriously
injure you or other bystanders.

Lower the cutting units to the ground, set the
parking brake, and remove the key from the ignition
switch when the machine is not in use.

G014556

III

Figure 20

Ignition switch

Engine-Preheat-Indicator Light

Turn the ignition key to position

. The engine preheat

indicator light illuminates and heats the glow plugs
(

Figure 21

Important:

Attempting to start a cold engine before

the preheat is used can cause unnecessary wear to the
battery.

To start a cold engine, refer to

Starting a Cold Engine (page

26)

Figure 21

Engine-preheat-indicator light

Fuel Gauge

The fuel gauge shows the amount of fuel in the tank
(

Figure 22

G014558

FUEL

Figure 22

Hour Meter

The hour meter shows the total hours that the machine has
been operated (

Figure 23

G014559

000.0

Figure 23

Hour meter

Transmission-Neutral-Indicator Light

This light illuminates when the travel-control pedal is in the
N

EUTRAL

position and the ignition key is turned to position

(

Figure 24

Note:

The parking brake must be engaged for the

transmission neutral indicator light to illuminate.

Figure 24

Transmission-neutral-indicator light

Содержание 30659 LT-F3000





























































Результаты поиска

Содержание 30659 LT-F3000

Отзывы:

Похожие инструкции для 30659 LT-F3000

Бренды по названию

Популярные бренды

Toro 30659 LT-F3000, Руководство оператора

Результаты поиска

Содержание 30659 LT-F3000

Отзывы:

Похожие инструкции для 30659 LT-F3000

Бренды по названию

Популярные бренды