manualshive.com logo in svg

Toro 30487TC, Руководство оператора

Поделиться
Скачать
Toro 30487TC Скачать руководство пользователя страница 34

Maintenance Service

Interval

Maintenance Procedure

Every 400 hours

• Change the cutting-unit gearbox lubricant.
• Service the air-cleaner filter. —service the filter also when the air-cleaner indicator

shows red; service the air-cleaner filter more frequently in extremely dusty or dirty
conditions.

• Service the air cleaner.
• Replace the fuel-filter canister for the water separator.
• Drain water or other contaminants from the water separator.
• Inspect the fuel lines and connections.

Every 800 hours

• Drain and clean the fuel tank.
• Change the hydraulic fluid and filter.
• Inspect the engine-valve clearance. Refer to your engine owner’s manual.

Every 1,500 hours

• Replace moving hoses.

Before storage

• Drain and clean the fuel tank.

Every 2 years

• Flush and replace the cooling-system fluid.

Important:

Refer to your engine owner’s manual for additional maintenance procedures.

Note:

Download a free copy of the electrical or hydraulic schematic by visiting www.Toro.com and searching

for your machine from the Manuals link on the home page.

Important:

The fasteners on the covers of this machine are designed to remain on the cover after

removal. Loosen all the fasteners on each cover a few turns so that the cover is loose but still attached,
then go back and loosen them until the cover comes free. This prevents you from accidentally stripping
the bolts free of the retainers.

34

 

Содержание 30487TC





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды