Toro 30314TE Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 48

background image

34

Note: Now is the best time to install a new fuel filter
because the fuel tank is empty. Refer to Replacing the
Fuel Filter; page 34.

5. Install the fuel line onto the valve. Slide the hose

clamp close to the valve to secure the fuel line.

1

2

m–5185

Figure 40

1.

Fuel shut-off valve

2.

Clamp

Servicing the Fuel Filter

Service Interval/Specification

Replace the fuel filter after every 200 operating hours or
yearly, whichever occurs first.

Replacing the Fuel Filter

Never install a dirty filter if it is removed from the fuel
line.

Note: Note how the fuel filter is installed.

1. Disengage the PTO and set the parking brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Close fuel shut–off valve at fuel tank (Fig. 40).

4. Squeeze the ends of the hose clamps together and slide

them away from the filter (Fig. 41).

5. Remove the filter from the fuel lines.

6. Install a new filter and move the hose clamps close to

the filter.

7. Open fuel shut-off valve at fuel tank (Fig. 40).

8. Check for fuel leaks and repair if needed (Fig. 40).

3

2

1

m–5234

3

1

Figure 41

1.

Hose clamp

2.

Fuel line

3.

Filter

Servicing the Cutting Blades

To ensure a superior quality of cut, keep the blades sharp.
For convenient sharpening and replacement, you may
want to keep extra blades on hand.

A worn or damaged blade can break, and a piece
of the blade could be thrown into the operator’s
or bystander’s area, resulting in serious personal
injury or death.

•

Inspect the blade periodically for wear or
damage.

•

Replace a worn or damaged blade.

Warning

Before Inspecting or Servicing the
Blades

Park the machine on a level surface, disengage the blade
control (PTO) and set the parking brake. Turn the ignition
key to off. Remove the key and disconnect the spark plug
wire(s) from the spark plug(s).

Inspecting the Blades

1. Inspect the cutting edges (Fig 42). If the edges are not

sharp or have nicks, remove and sharpen the blades.
Refer to Sharpening the Blades on page 35.

«
...
32
33
34
35
36
...
»

Содержание 30314TE

















































Отзывы:

Нет отзывов

Похожие инструкции для 30314TE

Бренд: Yard Machines Страницы: 20

Бренд: Yard Machines Страницы: 32

YP21KH42 (96041031300)

Бренд: Yard Pro Страницы: 20

Бренд: Parkside Страницы: 60

Бренд: Yard-Man Страницы: 16

ELM 34/1400 PLUS

Бренд: F.F. Group Страницы: 48

Бренд: Simplicity Страницы: 4

Бренд: Cub Cadet Страницы: 1

Бренд: Cub Cadet Страницы: 2

Бренд: Toro Страницы: 64

Бренд: Ferrari Страницы: 56

Бренд: Scotts Страницы: 66

Бренд: Schulte Страницы: 170

Бренд: Kärcher Страницы: 21

Бренд: Sun Lawn Страницы: 12

Бренд: ST. SpA Страницы: 21

PowerMax 32 E 4033

Бренд: Gardena Страницы: 11

Бренд: Gardena Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды