Toro 23208 Скачать руководство пользователя страница 29

Страница: 29 / 44

Removing the Battery

Park the machine on a level surface, engage
the parking brake (if applicable), and lower the
grinder.

Shut off the engine and remove the key.

Lift the black rubber cover on the negative cable.
Disconnect the negative battery cable from the
negative (-) battery terminal (

Figure 38

g008335

Figure 38

Negative cable

Positive cable

Nut (1/4 inch)

Battery hold down plate

Nut (5/16 inch)

Washer

Bolt

10.

J-bolt

Rubber cover (red)

11.

Battery

Rubber cover (black)

Slide the red terminal boot off the positive (red)
battery terminal, then remove the positive (red)
battery cable (

Figure 38

Remove the hold down plate, J-bolts, and
locknuts securing the battery (

Figure 38

) and

remove the battery.

Charging the Battery

WARNING

Charging the battery produces gasses that
can explode.

Never smoke near the battery and keep sparks
and flames away from battery.

Important:

Always keep the battery fully charged

(1.265 specific gravity). This is especially
important to prevent battery damage when the
temperature is below 0°C (32°F).

Remove the battery from the machine; refer to

Removing the Battery (page 29)

Charge the battery at a rate of 3 to 4 A for 4
to 8 hours (

Figure 39

). Do not overcharge the

battery.

g003792

Figure 39

Positive battery post

Red (+) charger lead

Negative battery post

Black (-) charger lead

When the battery is fully charged, unplug
the charger from the electrical outlet, then
disconnect the charger leads from the battery
posts (

Figure 39

Содержание 23208













































Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды

Toro 23208, Руководство оператора

Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды