Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p
WARNING!
Disconnect from air supply before changing accessories or servicing.
3
Maintain the grinder in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
3
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
3
Before each use check abrasive disc for condition. If worn or damaged replace immediately.
3
Ensure the speed rating (rpm) of the disc is the same as, or greater than, the speed rating of the grinder.
3
Ensure there are no flammable or combustible materials near the work area.
p
WARNING!
Always wear approved eye (or face) and hand protection when operating the grinder.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, grinder noise level may exceed 85dB in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the grinder. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
3
Avoid unintentional starting.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this grinder poses a health risk. It is the owners responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT
use the grinder for a task it is not designed to perform.
7
DO NOT
operate grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING! DO NOT
grind any materials containing asbestos.
7
DO NOT
carry the grinder by the hose, or yank the hose from the air supply.
7
DO NOT
force, or apply heavy pressure to, the grinder, let the tool do the work.
7
DO NOT
place air line attachments close to your face and do not point at other people or animals.
7
DO NOT
operate grinder when you are tired or under the influence of alcohol, drugs or intoxicating
medication.
7
DO NOT
use grinder where there are flammable liquids, solids or gases such as paint solvents and including
waste wiping or cleaning rags etc.
7
DO NOT
carry the grinder with your finger on the power lever.
7
DO NOT
direct air from the air line at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
SA44 - 2 -250205
ITEM PART NO. DESCRIPTION
1
SA44T/01 MOTOR HOUSING
2
SA44T/02 SPRING PIN
3
SA44T/03 AIR INLET
4
SA44T/04 TRIGGER
5
SA44T/05 VALVE STEM
6
SA44T/06 BUSHING
7
SA44T/07 O-RING
8
SA44T/08 VALVE SPRING
9
SA44T/09 THROTTLE VALVE HOUSING
10
SA44T/10 THROTTLE LEVER PLUG
11
SA44T/11 O-RING
12
SA44T/12 PLUNGER
13
608ZZ
BEARING
14
SA44T/14 END PLATE
15
SA44T/15 ROTOR
16
SA44T/16 ROTOR BLADE
17
SA44T/17 SPRING PIN
18
SA44T/18 CYLINDER
19
SA44T/19 FRONT PLATE
ITEM PART NO. DESCRIPTION
20
6201Z
BEARING
21
SA44T/21 LOCK NUT
22
SA44T/22 BEVEL PINION
23
SA44T/23 COUPLING NUT
24
SA44T/24 SCREW
25
SA44T/25 DEFLECTOR
26
SA44T/26 SPACER
27
SA44T/27 SCREW
28
626ZZ
BEARING
29
SA44T/29 RETAINING RING
30
SA44T/30 BEVEL GEAR
31
SA44T/31 WAVE WASHER
32
6202ZZ
BEARING
33
SA44T/33 SPINDLE
34
SA44T/34 KEY
35
SA44T/35 GASKET
36
SA44T/36 RETAINER
37
SA44T/37 DISC COVER
38
SA44T/38 FLANGE
ITEM PART NO. DESCRIPTION
39
PTC/100G GRINDING DISC
40
SA44T/40 FLANGE NUT
41
SA44T/41 ADJUST SCREW
42
SA44T/42 ADJUST NUT
43
SA44T/43 CAP SCREW
44
SA44T/44 WASHER
45
SA44T/45 SPRING
46
SA44T/46 GOVERNOR
47
SA44T/47 PENDULUM
48
SA44T/48 SPRING PIN
49
SA44T/49 O-RING
50
SA44T/50 TORSION SPRING
51
SA44T/51 LEVER LOCK
52
SA44T/52 SPRING PIN
53
SA44T/53 SPANNER
54
SA44T/54 PIN WRENCH
55
SA44T/55 HANDLE
PARTS LIST FOR:
100mm EXTRA HEAVY DUTY ANGLE
GRINDER
Model:
SA44
DANGER OF FIRE/EXPLOSION HAZARD
o
o
WARNING! The grinding process can produce streams of sparks which are a potential source of ignition especially when grinding metal.
7
7
DO NOT use the grinder where there are flammable liquids, solids or gases.
7
7
DO NOT allow grinder sparks to make contact with the operators clothing or any other fabric such as cleaning rags. Fabrics
contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
3
3
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
preference to man-made fibres.
INSTRUCTIONS FOR:
100mm EXTRA HEAVY DUTY
ANGLE GRINDER
Model:
SA44
Issue: . . . . . . . . . . . . .2
Issue Date: . . . .100305
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
E-mail: [email protected]
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
