Toro 23208 Скачать руководство пользователя страница 3

Страница: 3 / 44

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Contents

Safety ....................................................................... 4

General Safety ................................................... 4
Safety and Instructional Decals .......................... 4

Setup ........................................................................ 8

1 Installing the Grinder Control Lever .................. 8
2 Checking the Fluid Levels ................................ 8
3 Charging the Battery ........................................ 8

Product Overview ..................................................... 9

Controls ............................................................. 9
Specifications .................................................. 12
Attachments/Accessories ................................. 12

Before Operation ................................................. 13

Before Operation Safety ................................... 13
Adding Fuel ...................................................... 13
Performing Daily Maintenance.......................... 14

During Operation ................................................. 14

During Operation Safety ................................... 14
Starting the Engine ........................................... 15
Driving the Machine .......................................... 16
Shutting off the Engine...................................... 16
Grinding a Stump.............................................. 16
Operating Tips ................................................. 17

After Operation .................................................... 17

After Operation Safety ...................................... 17
Moving a Non-Functioning Machine.................. 17
Securing the Machine for Transport .................. 18
Lifting the Machine ........................................... 18

Maintenance ........................................................... 19

Maintenance Safety.......................................... 19

Removing the Cover Plate ................................ 21
Removing the Bottom Shield ............................ 21

Lubrication .......................................................... 22

Greasing the Machine....................................... 22

Engine Maintenance ........................................... 23

Engine Safety ................................................... 23

Servicing the Air Cleaner .................................. 23
Servicing the Engine Oil.................................... 24
Servicing the Spark Plug(s) .............................. 26

Fuel System Maintenance ................................... 27

Draining the Fuel Tank ...................................... 27
Replacing the Fuel Filter ................................... 28

Electrical System Maintenance ........................... 28

Electrical System Safety ................................... 28
Servicing the Battery......................................... 28
Replacing the Fuses ......................................... 30

Drive System Maintenance .................................. 31

Servicing the Tracks ......................................... 31

Belt Maintenance ................................................ 33

Replacing the Pump-Drive Belt ......................... 33

Controls System Maintenance ............................. 34

Adjusting the Traction-Control

Alignment...................................................... 34

Hydraulic System Maintenance ........................... 37

Hydraulic System Safety................................... 37
Hydraulic Fluid Specifications ........................... 37
Checking the Hydraulic-Fluid Level................... 37
Replacing the Hydraulic Filter ........................... 38
Changing the Hydraulic Fluid ............................ 38

Grinder Maintenance............................................ 39

Replacing the Teeth .......................................... 39

Cleaning .............................................................. 40

Removing Debris from the Machine .................. 40

Storage ................................................................... 41

Storage Safety.................................................. 41
Storage............................................................. 41

Troubleshooting ...................................................... 42

Содержание 23208













































Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды

Toro 23208, Руководство оператора

Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды