Toro 23208 Скачать руководство пользователя страница 9

Страница: 9 / 44

Product Overview

g018769

Figure 4

Reverse safety
plate

Battery

Track

Control panel

Tie-down/lift
point

Chip shield

Engine

Parking-brake
lever
(machines with
CE kit only)

Grinder

Controls

Become familiar with all the controls (

Figure 5

) before

you start the engine and operate the machine.

Control Panel

g025098

Figure 5

Key switch

Traction control

Throttle lever

Reference bar

Choke lever

Grinder
control/hydraulic-lift lever

Hour meter

Key Switch

The key switch, used to start and shut off the engine,
has 3 positions: O

, R

, and S

TART

. Refer to

Starting the Engine (page 15)

Throttle Lever

Move the control forward to increase the engine speed
and rearward to decrease the engine speed.

Choke Lever

Before starting a cold engine, move the choke lever
forward. After the engine starts, regulate the choke
to keep the engine running smoothly. As soon as
possible, move the choke lever all the way rearward.

Note:

A warm engine requires little or no choking.

Hour Meter

The hour meter displays the number of hours of
operation that have been logged on the machine.

Содержание 23208













































Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды

Toro 23208, Руководство оператора

Результаты поиска

Содержание 23208

Отзывы:

Похожие инструкции для 23208

Бренды по названию

Популярные бренды