Toro 23208 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 44

background image

Adjusting the Traction-Control
Neutral Position

If the machine creeps forward or backward when
the traction control is in neutral and the machine is
warm, you may need to adjust the return-to-neutral
mechanism on the pumps; contact your Authorized
Service Dealer.

Adjusting the Traction-Control
Forward Position

If the machine does not drive straight when you hold
the traction control forward against the reference bar,
complete the following procedure:

1.

Drive the machine with the traction control
against the reference bar, noting which direction
the machine veers.

2.

Release the traction control.

3.

If the machine veers to the

left

, loosen the

right

jam nut and adjust the tracking set screw on the
front of the traction control (

).

4.

If the machine veers to the

right

, loosen the

left

jam nut and adjust the tracking set screw on the
front of the traction control (

).

g004194

Figure 52

1.

Set screw

3.

Stop

2.

Jam nut

5.

Repeat the procedure until the machine drives
straight in the full forward position.

Important:

Ensure that the set screws touch

the stops in the full forward position to avoid
overstroking the hydraulic pumps.

36

«
...
34
35
36
37
38
...
»

Содержание 23208













































Отзывы:

Нет отзывов

Похожие инструкции для 23208

Бренд: MACAP Страницы: 6

Бренд: KNECHT Страницы: 40

Бренд: Metabo Страницы: 20

Бренд: Ozito Страницы: 10

Бренд: MK Diamond Products Страницы: 24

Бренд: Princess Страницы: 16

Бренд: Desoutter Страницы: 36

VARILEX Akku 6112-5.0

Бренд: eisenblatter Страницы: 24

Бренд: Worx Страницы: 132

Бренд: MACAP Страницы: 24

Бренд: Sparky Group Страницы: 122

Бренд: Dynaset Страницы: 9

Бренд: Alpha tools Страницы: 28

Бренд: Rikon Power Tools Страницы: 20

Бренд: Rikon Power Tools Страницы: 22

Бренд: Power Craft Страницы: 75

Pro grinder MG1700

Бренд: Campomatic Страницы: 14

Бренд: Raider Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды