Toro 07320 Скачать руководство пользователя страница 4

1

Preparing the Machine

No Parts Required

Procedure

1.

Park the machine on a level surface.

2.

Engage the parking brake.

3.

Raise the bed until the prop rod is fully engaged;
refer to the

Operator’s Manual

.

4.

Shut off the engine and remove the key.

5.

Disconnect the battery; refer to the

Operator’s

Manual

.

2

Removing the ROPS
Assembly

No Parts Required

Removing the ROPS Assembly

If your machine does not have a ROPS assembly,
proceed to step

3 Installing the Compression

Spring (page 4)

.

Remove the bolts and nuts that secure the ROPS
assembly to the frame of the machine as shown in

Figure 1

and remove the ROPS assembly.

Note:

Do not remove the seat belt anchors that are

secured on the frame.

g026674

g026674

Figure 1

3

Installing the Compression
Spring

Parts needed for this procedure:

2

Compression spring

Procedure

Important:

For 2015 and older models, you must

order the 2 compression springs (Toro Part No.
117-4847) for installation.
For 2016 and newer models, the compression
springs are included in this kit.

1.

Raise the front of the machine off the ground
and support it with jack stands.

2.

Remove the current shock assemblies as shown
in

Figure 2

.

g026473

Figure 2

3.

Using a spring compressor, remove the current
springs and install the springs from this kit.

4.

Install the shock assemblies and turn them 3
clicks up from the longest position.

Note:

Refer to the

Service Manual

for further

instructions on replacing the spring and checking
the front end toe of the tires.

5.

Torque the bolts to 95 to 122 N∙m (70 to 90 ft-lb).

4

 

Содержание 07320













Отзывы: