Toro 03860 Скачать руководство пользователя страница 5

5

Assembly

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use the chart below to verify all parts have been shipped.

DESCRIPTION

QTY.

USE

Decal

1

Apply over existing decal for CE

Operator’s Manual

1

Read before operating machine.

Parts Catalog

1

Use for ordering replacement parts.

Registration Card

1

Fill out and return to Toro.

Inspection

After the cutting unit is unboxed, inspect the
following:

1. Check each end of the reel for grease. Grease should

be visibly evident in the reel bearings and internal
splines of reel shaft.

2. Ensure that all nuts and bolts are securely fastened.

3. Make sure carrier frame suspension operates freely and

does not bind when moved back and forth.

Adjusting Front Shield

Adjust front shield for desired grass clippings
dispersion.

1. Position cutting unit on a flat level surface.

2. Loosen flange head capscrew securing shield to right

side plate. Move shield to desired angle and tighten
screw (Fig. 2).

1

2

3

4

Figure 2

1.

Front grass shield

2.

Front capscrew

3.

Rear grass shield

4.

Rear capscrew

Adjusting Rear Shield

Under most conditions, best dispersion is attained
when rear shield is closed (front discharge). When
conditions are heavy or wet, rear shield may be
opened.

1. To open rear shield

 

(Fig. 2), loosen flange head

capscrew securing shield to right side plate, rotate
shield to open position and tighten capscrew.

Содержание 03860

















Отзывы: