Toro 03860 Скачать руководство пользователя страница 4

4

Specifications

Reel Construction: Fairway reels. All welded. 5, 7
or 11 blades.

Recommended Height Of Cut Range:
5 Blade
 – 1” to 1-3/4” (25–44 mm) 
7 Blade – 1/2” to 1” (13–25 mm)
11 Blade – 3/8” to 3/4”  (10–19 mm)

Note: Use bedknife Part No. 93-9774 for

heights-of-cut below 1/2” (13 mm).

Reel Diameter: 7 in.  (178 mm)

Power Attachment: Reel motors feature quick
disconnect for removal or installation onto cutting
unit. Cutting units can be driven from either end.

Height–of–cut & Roller Adjustment: Height-of-cut
adjustment is made at the rear roller with threaded
micro–adjustment. Front roller position is adjustable
to set cutting unit attitude.

Bedknife And Bedbar Adjustment: Single point
adjustment (SPA) mechanism.

Selected Clip Control: The Reelmaster 5500
Traction Unit is equipped with manually adjustable
reel speeds which control selected clip.

Note: Refer to Traction Unit Operator’s Manual

for proper set–up procedure.

Automatic Clip Control: The Reelmaster 6000
Series Traction Unit is equipped with an electronic
controller which is programmed to achieve automatic
clip control. As the traction unit speed varies, the
controller will automatically adjust the hydraulic flow
to the reel motors to vary reel speed and maintain
proper clip. For proper clip, the controller needs to
know what cutting units are installed (5, 7 or 11
blade) and the height-of-cut.

Note: Refer to Traction Unit Operator’s Manual

for proper set–up procedure.

Rollers: Front roller is a 3” (76 mm) diameter cast
Wiehle roller. Rear roller is a 3” (76 mm) diameter
steel full roller. Both rollers use heavy duty ball
bearings with two conventional single lip seals and a
Toro labyrinth seal to provide four sealing surfaces to
protect the bearings.

Optional Equipment

Dethatching Cutting Unit

Model No. 03872

Grass Basket Kit

Model No. 03882

Rear Roller Brush Kit

Model No. 03875

High Torque Reel Motor

Part No. 98-9998

Comb/Scraper Kit

Part No. 104–1845

Wiehle Roller Scraper

Part No. 100-9908

Rear Roller Scraper Kit

Part No. 100-9920

RM6000 Shoulder Wiehle Roller

Part No. 99-8675

RM5500 Shoulder Wiehle Roller

Part No. 100-9911

RM6000 Shoulder Wiehle Scraper

Part No. 99-8670

RM5500 Shoulder Wiehle Scraper Part No. 100-9913

3” Diameter Collar Kit

Part No. 104–8215

Low Height-of-Cut Bedknife*

Part No. 93-9774

Gauge Bar Assembly

Part No. 98-1852

Angle Indicator

Part No. 99-3503

Backlapping Brush Assembly

Part No. 29–9100

Bedknife Screw Tool

Part No. TOR510880

Cutting Unit Tool Kit

Part No. TOR4070

Reel Drive Tool

Part No. TOR4074

For height-of-cut below 1/2” (13 mm)

 Supplied with tractor

Содержание 03860

















Отзывы: