Toro 03860 Скачать руководство пользователя страница 11

11

C. Leveling Front Roller

Important

 

Toro strongly recommends the use of a

leveling plate when setting–up or adjusting any reel type
cutting unit. The leveling plate will help to ensure
accurate and consistent adjustments. Contact your local
Toro Distributor for ordering a leveling plate.

1. Position cutting unit on a flat surface.

2. Position a  straight, parallel sided bar under the reel

blades and against the front edge of the bedknife
(Fig. 11). For 1” (25 mm) height-of-cut or below, a
3/4” (19 mm) bar is recommended. For heights–of–cut
above 1” (25 mm), a 1–1/4” (32 mm) bar is
recommended.

Note: The bar thickness does not affect the

adjustment. The recommended bars
keep the cutting unit more balanced
during the adjustment. Make sure the
bar covers the full length of the reel
blades and the outermost contact points
between the reel and bar are equal
distances from the center of the reel.

3. Rock cutting unit forward (on reel blades and steel

bar) until front roller contacts flat surface. Reel blades
and bedknife must maintain contact with bar. Rear
roller should not contact surface (Fig. 11).

4. Use a piece of newspaper or visually check to see if

any gap exists between front roller ends and flat
surface (Fig. 12). If needed, adjust front
height-of-cut rods until both ends of roller are in
contact with level surface.

Note: If leveling the front roller causes the

cutting unit attitude to be different
from side to side by more than one
degree, you may need to regrind the
reel and/or bedknife to eliminate
uneven wear.

Contact along full length of reel blade and front roller
ends levels front roller to reel.

Bar stock (3/4” thick

stock suggested)

Ref. flat surface
(1” x 20 x 30” flat
stock suggested)

Gap

Figure 11

Figure 12

Содержание 03860

















Отзывы: