tornos DECO 20 Headstock Revision Скачать руководство пользователя страница 5

Страница: 5 / 15

TT5503 − DECO 13a Headstock Revision − Ref. 307001

Chap. 2. / 5

TT5503 en − 12/04

EQUIPMENT

Assembly drawing

ref. 307001

Assembly drawing

ref. 307024

Press

travel

~600mm

Grease

Mobile 28
Kubler NBU15
Molykote DX

Headstock filling oil

ISO GV 220

Screw locking product

Loctite 243

DISMOUNTING THE HEADSTOCK

Actions

Notes

After dismounting the headstock from the machine :

1. Remove the thrust tube.

2. Remove the nipple screw (40).

⇒

Note :
Refer to the assembly drawings, ref. 307001
and 307024.

3. Remove the plugs (60), the tubings (70) and the

endpiece (140).
Then remove the gaskets.

4. Loosen the 8 front screws (200).

5. Remove the flange (80).

6. Push the flange to remove the thrust ring (320).

7. Remove the screws (360).

8. Tighten the screws (30) to release the spring

(330).

9. Using the press, remove the spindle.

Содержание DECO 20 Headstock Revision
















Результаты поиска

Содержание DECO 20 Headstock Revision

Отзывы:

Похожие инструкции для DECO 20 Headstock Revision

Бренды по названию

Популярные бренды

tornos DECO 20 Headstock Revision, Описание - Процедуры

Результаты поиска

Содержание DECO 20 Headstock Revision

Отзывы:

Похожие инструкции для DECO 20 Headstock Revision

Бренды по названию

Популярные бренды