Tornatech GPU Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 67

Tornatech GPU Скачать руководство пользователя страница 57

57

-Maximum: Value of maximum temperature displayed in the system actual unit and the moment it was reached.
-Average: Calculated value of the average temperature during that period displayed in the system actual unit.

-Generator( for transfer switch models only):
-Last Run: Date and time of the generator/second utility last run.
-Run time: Total running time of the generator/second utility during that period.
-Transfer Count: Number of times the power was transferred to the alternate side during that period.

All Time Statistics

History > All Time Statistics

All statistics shown here are calculated since the controller's first start-up was done. All dates are in the
YYYY.MM.DD format and all time references are in the HH:MM:SS format.

-First Power Up: Date and time of when the controller was first powered up.
-First Start Up: Date and time of when the controller's first start-up was completed.
-On Time: Total duration of controller powered on since the first power-up. In Day.Hour.Minutes.

Pressure Curves

Graphical Mode

History > Pressure Log Curves

The vertical axis represents the pressure in the actual unit selected. Its scale is dynamic and will resize depending
on the highest recorded value. The horizontal axis represents time and period. The left part of the horizontal axis
shows the beginning of the current scope and the right part shows the end of the scope. Located just right of the

«
...
55
56
57
58
59
...
»

Содержание GPU




































































Отзывы:

Нет отзывов