Tornatech GPU Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 67

Tornatech GPU Скачать руководство пользователя страница 33

33

character and the "CA" button clears the whole text field. Simply click the "OK" button once the value is set. This
type of text field is mostly used to generate a digital text indication for a custom alarm input.

Advanced Configuration Page

Config > Advanced

This page is the portal to all the advanced configuration parameters of the ViZiTouch.

All timers, sensors, factory settings, software update, service dealer and debug pages may be accessed simply by
clicking on the appropriate buttons.

Since two of the analog inputs are using the same physical connector, only one of these can be installed at once.
These analog inputs are shown in the grey box surrounded by a black dotted line. Each time one of these sensors
is installed, the other will turn orange, preventing the dual installation of these sensors.

All buttons are set to security "Level 0" except "Update Program" which is set at "Level 1" security.

Details of the Advanced Configuration Page

Timers Page

Config > Advanced > Timers1-2

«
...
31
32
33
34
35
...
»

Содержание GPU




































































Отзывы:

Нет отзывов